Why is the rinse water not hot enough in my Jackson TempStar Dishwasher?
If the rinse water in your Jackson Dishwasher isn't reaching the required temperature, check the rinse heater element for continuity; if it's open, replace the heater. Verify the operation and setting of the thermostats, replacing them if necessary. Consider replacing the rinse thermometer as well, as it may be defective.
Why is the wash water not hot enough in my Jackson TempStar Dishwasher?
If the wash water in your Jackson Dishwasher isn't reaching the required temperature, check the wash heater element for continuity; if it's open, replace the heater. Also, verify the operation and setting of the thermostats, replacing them if necessary. Replace the wash thermometer if it is defective.
What to do if my Jackson TempStar won't run, but it's filling and the power light is on?
If your Jackson Dishwasher is filling but won't run with the power light on, check if the timer is receiving power; if so, replace the timer assembly. Verify that the wash motor is getting power; if so, replace the motor. Also, check the wash motor contactor for continuity; if the contacts are open, replace the contactor.
Why is my Jackson TempStar filling slowly or has a weak rinse?
If your Jackson Dishwasher fills slowly or has a weak rinse, start by removing and cleaning the rinse arms, as they may be clogged or obstructed. Next, adjust the water pressure regulator to ensure a flow of 10 ± 2 PSI. Lastly, clean out the Y-strainer, as it might be clogged.
How to fix doors that won't close on Jackson TempStar Dishwasher?
If the doors of your Jackson Dishwasher won't close completely, adjust the spring tension by loosening (not removing) the spring bolt nuts. Then, tighten the nuts back when done. Remove any obstruction in the door channel. Adjust the frame to accommodate the doors if they are not square with the frame.
Why won't my Jackson Dishwasher rinse during the autocycle?
If your Jackson Dishwasher won't rinse during the autocycle, the rinse solenoid may be defective and require repair or replacement. The timer could also be faulty and need replacement. Verify that there is water at 10 ± 2 PSI connected to the machine.
Why is there no pressure indication on my Jackson TempStar Dishwasher?
If there's no pressure indication on your Jackson Dishwasher, first, ensure the water is turned on. Next, verify the wiring of the transducer. If the wiring is correct, the pressure transducer may be defective and need replacement.
Why is the rinse water not reaching the required temperature in my Jackson Dishwasher?
If the rinse water in your Jackson Dishwasher is not reaching the required temperature, check the rinse heater element for continuity; if it's open, replace the heater. Also, verify the operation and setting of the thermostats; replace if necessary. Replace the rinse thermometer if it is defective.
What to do if my Jackson TempStar Dishwasher doesn’t drain when turned off?
If your Jackson Dishwasher isn’t draining when you switch it off, here’s what to do: * Check for and remove any drain clogs. * Remove the standpipe and run the drain cycle again.
Why are the dishes not coming clean in my Jackson Dishwasher?
To address dishes not coming clean in your Jackson Dishwasher, first, ensure that the incoming water, rinse water, and wash water temperatures meet the minimum requirements specified on the machine's data plate. Next, adjust the detergent concentration to match the water volume in the machine. Finally, if you're using a solid dispenser, check and replace the canister if it's empty.
Details warranty terms for parts and labor.
Provides overall physical dimensions of the dishmachine.
Lists voltage, phase, frequency, and circuit requirements.
Steps for safe electrical connections.
Lists common issues and their causes/remedies.
Electrical diagram for Tempstar HH/HH-E (1-Phase).
Electrical diagram for LT/NB models (1-Phase).
General| Model | TempStar Series |
|---|---|
| Voltage | 208-240V |
| Number of Wash Cycles | 1 |
| Color | Stainless Steel |
| Category | Dishwasher |
| Voltage Options | 208V, 240V |
| Capacity | 60-80 racks per hour |
| Water Consumption per Cycle | 0.5-1.0 gallons |
| Water Consumption per Rack | 0.84 gallons |
To Next Page
