Jackson TempStar Series

Other manuals for Jackson TempStar Series

Installation, Operation & Service Manual78 pages

Questions and Answers

D
Deanna DoyleAug 26, 2025
Why does my Jackson Dishwasher run continuously in the wash cycle?
- A
  Ana RitterAug 26, 2025
  If your Jackson Dishwasher runs continuously in the wash cycle, it might be in delime mode. Change the operation mode from DELIME to NORMAL. If that's not the issue, the wash cycle delay timer could be faulty. If the red light isn't on during cycles B, C, or D, replace the cycle timer. Also, ensure the delay potentiometer is correctly adjusted for cycles B, C, or D. A faulty cam timer could also be the cause; in this case, also adjust the delay potentiometer for cycles B, C, or D. Confirm that the wash cycle delay timer is functioning correctly, that the timer motor is receiving power, and that there are no obstructions limiting the rotation of the cam timer.
H
harveydanielAug 27, 2025
What to do if my Jackson TempStar will not fill after the door is closed, but the power is on?
- J
  Jonathan SuttonAug 27, 2025
  If the Jackson Dishwasher will not fill after the door is closed but the power light is on, the rinse solenoid valve may be faulty, requiring repair or replacement. Another potential cause is a faulty door switch; verify its wiring, and if correct, replace the switch. Lastly, a fouled or faulty high-level probe could be the issue; clean the probe, and if it's still not working after cleaning, replace it.
B
Brooke TranAug 27, 2025
Why is my Jackson TempStar Dishwasher filling slowly, and the rinse is weak?
- D
  Diana VelasquezAug 28, 2025
  If your Jackson Dishwasher fills slowly or the rinse is weak, start by removing and cleaning the rinse arms, as they might be clogged or obstructed. Also, check the incoming water pressure and adjust the water pressure regulator to ensure it's at 20±5 PSI. Lastly, inspect the Y-strainer for clogs and clean it out if necessary.
V
Vanessa JosephAug 28, 2025
Why doesn't the wash or rinse heater work in my Jackson TempStar Dishwasher?
- D
  Debbie CollinsAug 29, 2025
  If the wash or rinse heater in your Jackson Dishwasher isn't working, check the heater element for continuity; if it's open, replace the heater. Another potential cause is a faulty heater contactor, which would also need replacement. Lastly, verify the operation and settings of the thermostats; replace them if necessary.
M
Michelle GibsonAug 29, 2025
Why will my Jackson TempStar Dishwasher not rinse during autocycle?
- D
  Darren ChavezAug 29, 2025
  If your Jackson Dishwasher will not rinse during the autocycle, the rinse solenoid might be defective and needs repair or replacement. Alternatively, the fill microswitch could be faulty and require replacement. Lastly, ensure the machine has a water supply at 20±5 PSI.
C
Christopher SmithAug 30, 2025
Why is the wash water not reaching the required temperature in my Jackson Dishwasher?
- B
  Brandon PowellAug 30, 2025
  If the wash water in your Jackson Dishwasher isn't reaching the required temperature, check the wash heater element for continuity; if it's open, replace the heater. Also, verify the operation and setting of the thermostats and replace if necessary. Finally, replace the wash thermometer if it's defective.
V
vlewisAug 23, 2025
What to do if my Jackson TempStar doesn’t drain?
- D
  Diamond ConleyAug 23, 2025
  If your Jackson Dishwasher isn’t draining when the power button is pressed, first, remove any obstruction from the drain. Then, remove the standpipe and run the drain cycle again. If the issue persists, the drain valve may be defective and require replacement.
J
Joseph AverySep 1, 2025
What to do if my Jackson TempStar will not fill after the door is closed, and the power is off?
- C
  Cameron DavisSep 1, 2025
  If the Jackson Dishwasher will not fill after the door is closed and the power light is not illuminated, the service breaker may have tripped and needs to be reset. Ensure the machine is properly connected to the power source. If the breaker trips again, contact an electrician to verify the amp draw of the machine.
J
James HunterSep 2, 2025
Why is there water leaking at the wash pump of my Jackson Dishwasher?
- D
  Diane AlvarezSep 2, 2025
  If water is leaking at the wash pump of your Jackson Dishwasher, the wash pump seal might be defective and needs replacement. Ensure the petcock or pump drain (if equipped) is shut and tight. Also, tighten any loose hoses or hose clamps on the wash pump.
J
Justin DaltonSep 3, 2025
How to fix doors that will not close completely on my Jackson Dishwasher?
- V
  Victoria NovakSep 3, 2025
  If the doors of your Jackson Dishwasher will not close completely, adjust the spring tension by loosening (not removing) the spring bolt nuts. Remove any obstructions in the door channel. Adjust the frame to accommodate the doors if they are not square with the frame.

Summary

MANUFACTURERS WARRANTY

ONE YEAR LIMITED PARTS AND LABOR WARRANTY

Details warranty terms for parts and labor.

NOMENCLATURE

GUIDES

SPECIFICATIONS

MACHINE DIMENSIONS

Provides overall physical dimensions of the dishmachine.

ELECTRICAL REQUIREMENTS

Lists voltage, phase, frequency, and circuit requirements.

INSTALLATION

ELECTRICAL POWER CONNECTIONS

Steps for safe electrical connections.

PROGRAMMING EXHAUST FAN TIMER

TROUBLESHOOTING

COMMON PROBLEMS

Lists common issues and their causes/remedies.

SCHEMATICS

TEMPSTAR;TEMPSTAR HH;HH-E SCHEMATIC

Electrical diagram for Tempstar HH/HH-E (1-Phase).

LT & NB, 208;230 V, 50;60 HZ, 1-PHASE

Electrical diagram for LT/NB models (1-Phase).

ADDENDUM

EXTERNAL DEVICE WIRING

Jackson TempStar Series Specifications

General

Model	TempStar Series
Voltage	208-240V
Number of Wash Cycles	1
Color	Stainless Steel
Category	Dishwasher
Voltage Options	208V, 240V
Capacity	60-80 racks per hour
Water Consumption per Cycle	0.5-1.0 gallons
Water Consumption per Rack	0.84 gallons