EasyManuals Logo

Johnson Controls (H,Y,C)IDM012B21S User Manual

Johnson Controls (H,Y,C)IDM012B21S
668 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #333 background imageLoading...
Page #333 background image
CONTROL SYSTEM
TC-15001-rev.3
6-17
 (OHFWULFDO:LULQJ
:LULQJ([DPSOHXVLQJDVKLHOGHGFRPPXQLFDWLRQFDEOH
Max. 16 Indoor Units
Controller
Electrical Box
of Indoor Unit
Electrical Box
of Indoor Unit
Terminal Board Terminal Board
M3.5
Screws
M3.5
Screws
Shield Communication Cable: 1P- AWG 18 (0.82mm
2
) or more
AA
BB
CN1
$77(17,21
$OZD\VPDNHVXUHWRWXUQ2))WKHSRZHURIWKHLQGRRUXQLWZKHQSHUIRUPLQJHOHFWULFDOZLULQJZRUN
3HUIRUPLQJHOHFWULFDOZLULQJZRUNZLWKWKHSRZHURQFDQGDPDJHWKHFLUFXLWERDUGVRIWKHLQGRRUXQLWVDQG
the controller.
A. Use AWG 22 (0.32mm
2
) to AWG 18 (0.82mm
2
) cable (Max. total cable length 98 ft. 4-13/16 in. (30m)).
If the total cable length is longer than 98 ft. 4-13/16 in. (30m), use communication cable (1P to AWG 18
(0.82mm
2
)) (Max. total cable length 1,640 ft. 6 in. (500m)). Communication cabling shall be a minimum of
18-Gauge, 2-Conductor, Stranded Copper. Shielded cable must be considered for applications and routing
LQDUHDVRIKLJK(0,DQGRWKHUVRXUFHVRISRWHQWLDOO\H[FHVVLYHHOHFWULFDOQRLVHWRUHGXFHWKHSRWHQWLDOIRU
communication errors. When shielded cabling is applied, proper bonding and termination of the cable
shield is required as per Johnson Controls guidelines. Plenum and riser ratings for communication cables
must be considered per application and local code requirements.
B. Keep a distance of more than 11-13/16 in. (30cm) between the controller / indoor unit communication
cables and the power wiring.
& ,ILQVWDOOHGZLWKLQLQFPSXWWKHFDEOHVLQDFRQGXLWWXEHDQGJURXQGW\SH'ȍRQHHQG
RIWKHSLSH:LWKRXWWKLVSURFHGXUHPDOIXQFWLRQRUIDLOXUHRIWKHLQGRRUXQLWEHFDXVHRI(OHFWURPDJQHWLF
,QWHUIHUHQFH(0,PD\RFFXU
D. When multiple indoor units are simultaneously controlled, set addresses for refrigerant cycle and indoor
XQLWV(VSHFLDOO\ZKHQLQGRRUXQLWVIURPPXOWLSOHUHIULJHUDQWF\FOHVDUHVLPXOWDQHRXVO\FRQWUROOHG
transmission abnormality may occur because of address duplication.
( )RUPRUHLQIRUPDWLRQDERXWZLULQJFRQWUROOHULQGRRUXQLWDQGVHWWLQJLQGRRUXQLWVDGGUHVVHVUHIHUWRWKH
LQGRRUXQLWV¶³,QVWDOODWLRQ0DQXDO´
F. Do not leave any spaces at the cable opening of the remote controller case. If there is any space, cover it
with vinyl tape to avoid trouble caused by condensate or insects entering the controller case.
NOTICE

Table of Contents

Other manuals for Johnson Controls (H,Y,C)IDM012B21S

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Johnson Controls (H,Y,C)IDM012B21S and is the answer not in the manual?

Johnson Controls (H,Y,C)IDM012B21S Specifications

General IconGeneral
BrandJohnson Controls
Model(H, Y, C)IDM012B21S
CategoryAir Conditioner
LanguageEnglish

Related product manuals