Kemper 360 - Page 4

Contents
Page
Harvesting Unit Method of
Operation—Higher Yields Through
Narrow Corn Row Spacing.............................302
Operating the Harvesting
Unit—General Use .........................................302
Corn Harvesting  Normal Harvesting
Conditions ......................................................302
Corn Harvesting  Down Crop ............................303
Harvesting ShortStemmed Corn .......................304
Whole Crop Silage..............................................304
Technical Retrofitting to WholeCrop
Silage (WCS) Harvest ....................................306
Harvesting Crop with Very Close or
Wide Row Spacing (345, 360 and 375) ....... 3011
LengthofCut Adjustment with CLAAS
Forage Harvester .........................................3012
Length of Cut and Drum Speeds with
CLAAS Forage Harvester 860880
(Type 491) ....................................................3012
Length of Cut and Drum Speeds with
CLAAS Forage Harvester 830900
(Type 492) ....................................................3013
Length of Cut and Drum Speeds with
CLAAS Forage Harvester 830900
(Type 493) ....................................................3014
Length of Cut and Drum Speeds with
CLAAS Forage Harvester 930980
(Type 494) ....................................................3020
LengthofCut Adjustment with NEW
HOLLAND and CASE Forage Harvester .....3022
Length of Cut and Drum Speeds with
NEW HOLLAND and CASE Forage
Harvester......................................................3024
Length of Cut and Drum Speeds with
KRONE Forage Harvester ...........................3025
Adjusting Harvesting Unit Lateral Float
(Optional on 345 and 360, Standard
on 375) .........................................................3025
Adjusting the Feed Bars (330, 345 and 360)....3026
Adjusting the Feed Bars (375 up to
Construction Year 2009)...............................3027
Adjusting the Feed Bars (375 from
Construction Year 2010)...............................3028
Adjusting the Large Dividers.............................3029
Steering Assistance (Option)............................3030
Accessories
Special Kit for Row Guidance (Steering
Assistance).....................................................351
Automatic Height Control Kit ..............................351
Special Kit for WholeCrop Silage ......................351
Special Kit for Crops with Very Close
or Wide Row Spacing (345, 360 and 375) .....351
Special Kit for Quality of Cut...............................351
Troubleshooting
Correction of Defects on the Rotary
Harvesting Unit...............................................401
Page
Lubrication and Maintenance
Service Intervals .................................................451
Transmission Oil.................................................451
General View of Drives and Oil Levels
in the Rotary Harvesting Unit (Part 1) ............452
General View of Drives and Oil Levels
in the Rotary Harvesting Unit (Part 2) ............453
Overview of Oil Levels in Input Transmission.....454
Checking Oil Level and Changing Oil.................455
Lubricants...........................................................455
Coolant for Main Drive Friction Clutch................455
Alternative and Synthetic Lubricants ..................456
Mixing Lubricants................................................456
Lubricant Storage ...............................................456
Every 10 Hours  U.J. Shaft................................456
Every 10 Hours  Rotating Crop Divider .............457
Every 10 Hours  Lower Rolls of Tilt
Frame (If Equipped, Standard on
Model 375) .....................................................457
Every 50 Hours  Lower Axle Pin of
Hydraulic Cylinder and Frame Hinge Clutch ..457
Every 50 Hours  Hinges of Outer Sections........458
Once Every Year  RadialPin Clutch of
Gathering Drum..............................................458
Once Every Year  Upper Rolls of Tilt
Frame (If Equipped, Standard on
Model 375) .....................................................458
Every 3 Years  Change Coolant
of Main Drive Friction Clutch (If
Equipped, Standard on Model 375) ...............459
Before Start of Season .......................................459
Daily Maintenance (Or More Often if
Necessary) .....................................................459
Weekly Service.................................................4510
End of Season Maintenance ............................4510
Service
Metric Bolt and Screw Torque Values.................501
Main Drive Slip Clutches 
WaterCooled (Optional on 345 and
360, Standard on 375) ...................................502
Removal of Slip Clutch .......................................503
Disassemble Slip Clutch.....................................505
Main Drive Friction Clutches (330, 345
and 360) .........................................................506
Gathering, Cross Feed and Feed Drum
RadialPin Clutches........................................507
Feeding and Cutting Area...................................508
Crop Feed Area ................................................ 5011
Drive for DownCrop Auger ..............................5012
Storage
Storage at End of Harvesting Season ................551
Removing Harvesting Unit from Storage ............551
Specifications
330 Rotary Harvesting Unit ................................601
Continued on next page
ii
040810
PN=2