Keyscan CA250B User Manual

Keyscan Inc. – Technical Guide (PC109x - 04.15)
77
Figure 52 – Network Connection with NETCOM2 Rev. B with Multiple CIMs/ACUs
CIM 0
Jumper ON J4
COMMON AUX INPUTS - E
17 18 19 20 21 22 23 24
IOCB (COM1)
RX
TX
CPB/CB COMMS
(COM4)
H2
COMMON AUX INPUTS - E
17 18 19 20 21 22 23 24
IOCB (COM1)
RX
TX
CPB/CB COMMS
(COM4)
TD1
RD1
TD2
RD2
GND
RTS
CTS
GND
RTS
CTS
B3 B2 B1 B0
Diag
J2
RESET
-
CAN2
+
EGND
-
CAN1
+
GND
V +
(+12V)
SCKT1
PC106x
J1
J7
J8
J6
J5
CAN2
CAN1
1 2 1 2 1 2 1 2
Rx-COM
COM
CAN CAN-Tx
J3
J4
J9
J12
Power
Good
Fault
HDR1
J10
J11
COMMON AUX INPUTS - E
17 18 19 20 21 22 23 24
IOCB (COM1)
RX
TX
CPB/CB COMMS
(COM4)
TD1
RD1
TD2
RD2
GND
RTS
CTS
GND
RTS
CTS
B3 B2 B1 B0
Diag
J2
RESET
-
CAN2
+
EGND
-
CAN1
+
GND
V +
(+12V)
SCKT1
PC106x
J1
J7
J8
J6
J5
CAN2
CAN1
1 2 1 2 1 2 1 2
Rx-COM
COM
CAN CAN-Tx
J3
J4
J9
J12
Power
Good
Fault
HDR1
J10
J11
TD1
RD1
TD2
RD2
GND
RTS
CTS
GND
RTS
CTS
B3 B2 B1 B0
Diag
J2
RESET
-
CAN2
+
EGND
-
CAN1
+
GND
V +
(+12V)
SCKT1
PC106x
J1
J7
J8
J6
J5
CAN2
CAN1
1 2 1 2 1 2 1 2
Rx-COM
COM
CAN CAN-Tx
J3
J4
J9
J12
Power
Good
Fault
HDR1
J10
J11
Black
Green
Red
CIM 0
CIM 1
CIM n
Slave
Global
Master
Termination Jumpers ON
J5 & J6 / J7 & J8
first & last CIM
Connect EGND
terminal on all
CIMs to ground
lugs in ACU
metal
enclosures.
Global Master
Jumper ON - J3
CAT 5
CAN Bus
Slave - Jumper OFF - J3
H2
H2
Shield*
to ACU
ground
lug
*Insulate shield with PVC tubing such as
Alpha (p/n PVC10516 16 AWG) or
comparable insulator.
RS-232 - 5 conductor
shielded 22 AWG cable
CAT 5
CAN Bus
Termination Jumpers ON
J5 & J6 / J7 & J8
first & last CIM
Slave
H1
Slave - Jumper OFF - J3
H1
H1
White Orange
Orange
Blue
White Blue
Ground
White Orange
Orange
Blue
White Blue
Ground
White Orange
Orange
Blue
White Blue
Ground
KI-00469E-10-14
12 VDC to DPS15
- RS-232 Data Cable
- Control Board
- PC with network connection
- CIM
- NETCOM2B
- 10/100 Base-T Cable
- CAT 5 Cable – 2 twisted pairs
Parts List
to network
10/100 Base-T cable
to network
Bit Rate / Jumper Settings (0 = OFF / 1 = ON)
Bit CIM Control Board
J9 J10 J11 J16 – 1 2 6 S2 – 2 3
9600 0 0 1 0 0 0 0 0
19200 0 1 0 0 1 0 1 0
57600 1 0 0 0 0 1 0 1
115200 1 0 1 0 1 1 1 1
Bit Rate / Distance
Bit CAN Bus RS-232
9600 3280' (999.7 m) 49.2' (14.9 m)
19200 3280' (999.7 m) 49.2' (14.9 m)
57600 984' (299.9 m) 26.2' (7.9 m)
115200 262' (80 m) 9.84' (3 m)
Note
CIM 0 / NETCOM6B does not support a
reverse network connection. CIM 0 requires
a NETCOM6P for reverse network.
Server with Keyscan
Communication Application/
Service
12VDC
+
-
RESET
GND
TD RD DTRDCD I/O
EGND
RS-232TD RD POWER
LE DsLE Ds
PRO GRAM
PRO GRAM
S1
S2
O
N
1
2
3
4
5
6
Black Green Red
Red (+)
Black (-)
Connect shield to enclosure
ground lug at one end of RS-232
cable. Cut shield off at other end
and ensure it is islolated.
If using shielded Ethernet
cable, connect EGND
terminal on NETCOM2B/6B
to enclosure ground lug.
S3
NETCOM2
Rev. B

Keyscan CA250B Specifications

General

Brand	Keyscan
Model	CA250B
Category	Controller
Language	English