Kramer VS-88H2

Kramer Electronics Ltd.
VS-88H2 – Protocol 3000 Commands
78
Function
Description
Syntax
Parameters/Attributes
Example
VID?
LEGACY COMMAND.
Get video switch
state.
The GET
command identifies
input switching on
Step-in clients.
The SET
command is for
remote input
switching on Step-in
clients (essentially
via by the Web).
This is a legacy
command. New Step-
in modules support
the ROUTE
command.
COMMAND
#VID?out_id<CR>
FEEDBACK
~nn@VIDin_id>out_id<CR><LF>
in_id – Indicates the ID of the
input:
1 – HDMI IN 1
2 – HDMI IN 2
3 – HDMI IN 3
4 – HDMI IN 4
5 – HDMI IN 5
6 – HDMI IN 6
7 – HDMI IN 7
8 – HDMI IN 8
> – Connection character between
in and out parameters
out_id –Output number:
1 – HDMI OUT 1
2 – HDMI OUT 2
3 – HDMI OUT 3
4 – HDMI OUT 4
5 – HDMI OUT 5
6 – HDMI OUT 6
7 – HDMI OUT 7
8 – HDMI OUT 8
Get video switch state of
HDMI OUT 2:
#VID?2<CR>
VID-
PATTERN
Set test pattern on
output.
COMMAND
#VID-PATTERNout_index,pattern_id<CR>
FEEDBACK
~nn@VID-PATTERNout_index,pattern_id<CR><LF>
out_index – Number that
indicates the specific output:
1 – HDMI OUT 1
2 – HDMI OUT 2
3 – HDMI OUT 3
4 – HDMI OUT 4
5 – HDMI OUT 5
6 – HDMI OUT 6
7 – HDMI OUT 7
8 – HDMI OUT 8
pattern_id –Number of system
patterns:
1 – Color bars
2 – Ramp
3 – Solid White
4 – Solid Black
5 – Solid Red
6 – Solid Green
Switch PATTERN 1 to
HDMI OUT 3:
#VID-PATTERN3,1<CR>
VID-
PATTERN?
Get test pattern on
output.
COMMAND
#VID-PATTERN?out_index<CR>
FEEDBACK
~nn@VID-PATTERNout_index,pattern_id<CR><LF>
out_index – Number that
indicates the specific output:
1 – HDMI OUT 1
2 – HDMI OUT 2
3 – HDMI OUT 3
4 – HDMI OUT 4
5 – HDMI OUT 5
6 – HDMI OUT 6
7 – HDMI OUT 7
8 – HDMI OUT 8
pattern_id – Number of system
patterns
1 – Color bars
2 – Ramp
3 – Solid White
4 – Solid Black
5 – Solid Red
6 – Solid Green
Get test pattern on HDMI
OUT 3:
#VID-PATTERN?3<CR>
VMUTE
Set enable/disable
video on output.
Video mute
parameter 2 (blank
picture) is not
supported.
COMMAND
#VMUTEout_index,flag<CR>
FEEDBACK
~nn@VMUTEout_index,flag<CR><LF>
out_index – Number that
indicates the specific output:
1 – HDMI OUT 1
2 – HDMI OUT 2
3 – HDMI OUT 3
4 – HDMI OUT 4
5 – HDMI OUT 5
6 – HDMI OUT 6
7 – HDMI OUT 7
8 – HDMI OUT 8
flag – Video Mute
0 – Video enabled
1 – Video disabled
2 – Blank picture
Disable the video output on
HDMI OUT 2:
#VMUTE2,0<CR>
VMUTE?
Get video on output
status.
Video mute
parameter 2 (blank
picture) is not
supported.
COMMAND
#VMUTE?out_index<CR>
FEEDBACK
~nn@VMUTEout_index,flag<CR><LF>
out_index – Number that
indicates the specific output:
1 – HDMI OUT 1
2 – HDMI OUT 2
3 – HDMI OUT 3
4 – HDMI OUT 4
5 – HDMI OUT 5
6 – HDMI OUT 6
7 – HDMI OUT 7
8 – HDMI OUT 8
flag – Video Mute
0 – Video enabled
1 – Video disabled
2 – Blank picture
Get video on output 2
status:
#VMUTE?2<CR>