Kyocera FS-9530DN Service Manual

2GZ/2G1
1-4-25
8020 Punch motor problem (optional 3000-
sheet document finisher)
The LOCK signal of the punch motor is
detected for more than 500 ms while the
punch motor is operating.
Poor contact in the
connector termi-
nals.
Check the connection of connector on the
punch PWB and the continuity across the
connector terminals. Repair or replace if
necessary.
Defective punch
motor.
Replace the punch motor.
Defective PWB. Replace the punch PWB or finisher main
PWB and check for correct operation.
8030 Tray upper limit detection problem
(optional document finisher)
When the tray elevation motor raises a
tray, the ON status of the tray upper limit
sensor is detected.
The tray upper limit
sensor/push paper
sensor/surface
view sensor con-
nector makes poor
contact.
Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.
Defective tray
upper limit sensor/
push paper sensor/
surface view sen-
sor.
Replace the sensor.
Defective finisher
main PWB.
Replace the finisher main PWB and check
for correct operation.
8050 Paper conveying belt motor 1 prob-
lem (optional 3000-sheet document
finisher)
Paper conveying belt home position sen-
sor 1 does not turn off within 1.5 s.
Paper conveying belt home position sen-
sor 1 does not turn on within 2.5 s.
Jam 88 is indicated.
Poor contact in the
connector termi-
nals.
Check the connection of connector YC2 on
the internal tray PWB and the connector on
paper conveying belt motor 1, and the conti-
nuity across the connector terminals. Repair
or replace if necessary.
Defective paper
conveying belt
home position sen-
sor 1.
Replace paper conveying belt home position
sensor 1.
Defective paper
conveying belt
motor 1.
Replace paper conveying belt motor 1.
Defective PWB. Replace the internal tray PWB or finisher
main PWB and check for correct operation.
8060 Paper conveying belt motor 2 prob-
lem (optional 3000-sheet document
finisher)
Paper conveying belt home position sen-
sor 2 does not turn off within 1.5 s.
Paper conveying belt home position sen-
sor 2 does not turn on within 2.5 s.
Poor contact in the
connector termi-
nals.
Check the connection of connector YC6 on
the internal tray PWB and the connector on
paper conveying belt motor 2, and the conti-
nuity across the connector terminals. Repair
or replace if necessary.
Defective paper
conveying belt
home position sen-
sor 2.
Replace paper conveying belt home position
sensor 2.
Defective paper
conveying belt
motor 2.
Replace paper conveying belt motor 2.
Defective PWB. Replace the internal tray PWB or finisher
main PWB and check for correct operation.
Code Contents
Remarks
Causes Check procedures/corrective measures

Kyocera FS-9530DN Specifications

General

Maximum print size	297 x 420 mm
Paper tray media types	Bond paper, Envelopes, Labels, Plain paper, Recycled paper, Transparencies
ISO A-series sizes (A0...A9)	A3, A4, A5
ISO B-series sizes (B0...B9)	B4, B5
Maximum ISO A-series paper size	A3
Color	No
Duplex printing	Yes
Print technology	Laser
Maximum resolution	1800 x 600 DPI
Time to first page (black, normal)	3.5 s
Print speed (black, normal quality, A3)	26 ppm
Print speed (black, normal quality, A4/US Letter)	51 ppm
Memory type	DDR
Memory slots	1
Processor model	750FL
Processor family	PowerPC
Compatible memory cards	CF
Maximum internal memory	640 MB
Sound power level (standby)	51 dB
Sound pressure level (printing)	70 dB
Total input capacity	1200 sheets
Maximum input capacity	4200 sheets
Total number of input trays	2
Multi-Purpose tray input capacity	200 sheets
Wi-Fi	-
Cabling technology	10/100Base-T(X)
Ethernet LAN data rates	10, 100 Mbit/s
Supported network protocols (IPv4)	TCP/IP, IPX/SPX, AppleTalk, NetBEUI
Printing colors	Black
Maximum duty cycle	300000 pages per month
Page description languages	PCL 5e, PCL 6, PCL XL
Current rating	11.4 A
AC input voltage	120 V
AC input frequency	60 Hz
Power consumption (standby)	180 W
Power consumption (printing)	900 W
Power consumption (PowerSave)	4.5 W
Standard interfaces	Ethernet, Parallel, USB 2.0
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Mac operating systems supported	Mac OS X 10.0 Cheetah, Mac OS X 10.1 Puma, Mac OS X 10.2 Jaguar, Mac OS X 10.3 Panther, Mac OS X 10.4 Tiger, Mac OS X 10.5 Leopard, Mac OS X 10.6 Snow Leopard, Mac OS X 10.7 Lion
Other operating systems supported	Novell NetWare 4.x, Novell NetWare 5.x, Novell NetWare 6.x
Server operating systems supported	Windows Server 2003
Windows operating systems supported	Windows 2000, Windows 2000 Professional, Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 95, Windows 98, Windows 98SE, Windows ME, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64
Sustainability certificates	ENERGY STAR
Product color	White
Networking features	Fast Ethernet

Weight and Dimensions

Dimensions (WxDxH)	599 x 646 x 615 mm