Kyocera KM-8030

2FB/2FC-2.0
2-3-34
Connector Pin No. Signal I/O Voltage Description
YC1 1 24V I 24 V DC 24 V DC power input
Connected
to the DC
power
source PWB
2 PGND - - Power ground
3 SGND - - Signal ground
4 5V I 5 V DC 5 V DC power input
YC2 A1 CONT SENS O Analog Toner container sensor detection signal
Connected
to the
engine PWB
A2 MP TRY SW O 0/5 V DC MP tray switch: On/off
A3 MP PSD SW O 0/5 V DC MP paper length size switch: On/off
A4 MP PE SW O 0/5 V DC MP paper empty switch: On/off
A5 MP SOL RTN I 0/24 V DC MP solenoid (return): On/off
A6 MP SOL PUL I 0/24 V DC MP solenoid (activate): On/off
A7 FEED B SW O 0/5 V DC Feed switch 2: On/off
A8 DK SEL(I) I 0/5 V DC Deck PWB SEL signal
A9 DK RDY(O) O 0/5 V DC Deck PWB ready signal
A10 DK SCLK(I) I 0/5 V DC
(pulse)
Deck PWB clock signal
A11 DK SDO I 0/5 V DC
(pulse)
Deck PWB serial communication signal
A12 DK SDI O 0/5 V DC
(pulse)
Deck PWB serial communication signal
A13 SGND - - Signal ground
B1 CONT SET SW O 0/5 V DC Toner container detection switch: On/off
B2 MP DIG0 O 0/5 V DC MP paper width size switch: On/off
B3 MP DIG1 O 0/5 V DC MP paper width size switch: On/off
B4 MP DIG2 O 0/5 V DC MP paper width size switch: On/off
B5 MP MOT CLK I 0/5 V DC
(pulse)
MP feed motor clock signal
B6 MP MOT REM I 0/5 V DC MP feed motor: On/off
B7 MP MOT HLD I 0/5 V DC MP feed motor hold signal
B8 MP MOT
MODE
I 0/5 V DC MP feed motor mode signal
B9 MP MOT CW I 0/5 V DC MP feed motor CWB signal
B10 MAIN MOT
REM
I 0/24 V DC Drive motor: On/off
B11 MAIN MOT
ALM
O 0/5 V DC Drive motor alarm signal
B12 N.C - - Not used
B13 SGND - - Signal ground
YC3 1 SGND - - Signal ground
Connected
to the cas-
sette 1 level
sensor 1/2/
3, cassette 1
detection
sensor and
lift motor 1
2 LCF1 SW1 I 0/5 V DC Cassette 1 level sensor 1: On/off
3 5V O 5 V DC 5 V DC power output
4 SGND - - Signal ground
5 LCF1 SW2 I 0/5 V DC Cassette 1 level sensor 2: On/off
6 5V O 5 V DC 5 V DC power output
7 SGND - - Signal ground
8 LCF1 SW3 I 0/5 V DC Cassette 1 level sensor 3: On/off
9 5V O 5 V DC 5 V DC power output
10 SGND - - Signal ground
11 LCF1 SW4 I 0/5 V DC Cassette 1 detection sensor: On/off
12 5V O 5 V DC 5 V DC power output
13 LIFT MOT1 L O 0/24 V DC Lift motor 1: On/off
14 LIFT MOT1 H O 0/24 V DC Lift motor 1: On/off
YC4 1 SGND - - Signal ground
Connected
to feed
switch 2
2 FEED B SW I 0/5 V DC Feed switch 2: On/off
3 5V O 5 V DC 5 V DC power output