Leica mojo 3D - Page 133

To Next Page

To Previous Page

Leica mojo3D, Treatments 133

6. To load the selected treatment, tap the button. You are

returned to the main navigation screen.

To leave the current treatment loaded, tap the button. You are

returned to the main navigation screen.

Main Page

Default Chapter1
- User Manual1
- Table of Contents4
- Leica Mojo3D, Table of Contents6
- Leica Mojo3D, Table of Contents8
- Leica Mojo3D, Table of Contents10
1 System Overview12
- General Mojo3D System Information12
- Components of the Mojo3D System13
- Features and Specifications15
2 System Installation20
- Before Installation20
- Mojo3D Installation22
- Antenna Installation25
- SIM Card Installation29
3 Running the Mojo3D for the First Time32
- Starting up32
- Setting the Screen Calibration34
- Initial Setup Wizard35
- Menu Buttons at Right of Screen49
- Menu Buttons at Left of Screen51
- Specifying Data for Display52
- Zoom Buttons54
- View Modes55
- Error Notifications56
- Running the Setup Wizard at any Time60
- Changing System Settings61
- Vehicle Setup62
- Attached Device Selection63
- NMEA Configuration65
- Feature Unlock66
4 Setting Guidance Types68
- AB Parallel Guidance68
- A+ Heading Guidance70
- Fixed Contour Guidance72
- Pivot Guidance74
- Ultimate Curve Guidance76
- Stop Guidance79
- Guidance Management80
- Field Offset99
- Nudge101
5 Auto-Steer102
- Engage Auto-Steer102
- Tuning Auto-Steer Performance106
- Stationary Engage and Reverse Steering117
- Testing Auto-Steer123
6 Treatments128
- Starting a New Treatment129
- Load a Stored Treatment130
- Changing a Treatment Name131
- Creating a PDF Report of a Treatment132
- Deleting a Treatment134
- Exporting Treatment Data136
- Importing Treatment Data142
7 Automatic Section Control146
- Section Control Latency147
  - Calibrating the Section Control Latency Value148
  - Troubleshooting Latency Problems150
- Setting the Overlap Limit153
- Setting the Low-Speed Shutoff155
- Section Override Control157
8 Field Boundary158
- Create a New Field Boundary158
- Load a Stored Field Boundary160
- Changing a Field Boundary Name161
- Deleting a Field Boundary162
- Exporting Field Boundary Data163
- Importing Field Boundary Data169
9 Vehicles and Implements178
- Saving a Vehicle or Implement Configuration179
- Load a Vehicle or Implement Configuration181
- Renaming a Vehicle or Implement Configuration183
- Deleting Vehicle or Implement Configurations186
- Exporting Vehicle or Implement Configurations191
- Importing Vehicle and Implement Configurations195
10 Correction Sources202
- Network DGPS203
- Sbas209
- Gl1Detm211
- Network RTK215
- RTK Base Station (Internal Radio)221
11 NMEA Output226
- Configuring NMEA Output227
- Logging NMEA Data to USB230
- NMEA Sentences Available232
12 Virtual Wrench™ Remote Service234
- Virtual Wrench234
- Making a Service Request235
- Upgrading Software from Virtual Wrench236
- Upgrading Software Via USB Flash Drive238
- Restoring Previous Software Version240
- Backing up Current Software242
- Serial Numbers and Other System Information244
13 Care and Transport246
- Transport246
- Storage246
- Cleaning and Drying247
14 Safety Directions248
- General Introduction248
- Intended Use249
- Limits of Use251
- Responsibilities251
- Hazards of Use253
- Electromagnetic Compatibility (EMC)259
- FCC Statement, Applicable in U.S262
- ICES-003 Statement, Applicable in Canada263
- Labelling264
15 Technical Data268
- Mojo3D Display Technical Data268
- Mojo3D GPS Receiver Technical Data271
- Wireless Modules Technical Data273
  - HSDPA Wireless Module Technical Data273
  - CDMA Wireless Module Technical Data275
- Antennas Technical Data277
- Mojoxact Technical Data289
- Mojoxact GPS Receiver Technical Data292
- Mojoxact Plus Technical Data294
- Mojoxact Plus GPS Receiver Technical Data297
- Conformity to National Regulations299
16 International Limited Warranty, Software License Agreement306
Appendix A Mojo3D Enhancements308
- Mojo3D with Single Section Control308
- Mojo3D with Multi Section Control Kit313
- Mojo3D with Geopro Antenna320
- A.5 Redeeming a System Option Voucher320
- Mojo3D with Mojoxact Kit325
- Redeeming a System Option Voucher364
Appendix B Formatting USB Flash Drives366
Appendix Cgnu General Public License372
Appendix D Glossary of Terms374

Leica mojo 3D - Page 133

Table of Contents

Related product manuals