Lightware HDMI-3D-OPT-RX150RA - Operation; Front Panel Leds - Transmitter; Video Input Leds; Audio Input Leds

4. Operation HDMI-3D-OPT series – User's Manual 23
4
Operation
This chapter is about the powering and operating of the device describing the

Î 
Î 
Î 
Î 
Î 
Î 
Î 

Video Input LEDs
 The video source is not selected.
BLINKING: The video source is selected but signal is not
detected.
ON: The video source is selected and signal is detected.

all, video LEDs blink.
Audio Input LEDs
 The audio source is not selected.
BLINKING: The audio source is selected but no signal
is detected, regardless of the output mode

HDMI signal).
 Audio source is selected, the audio is
embedded to the output video stream.
 Audio source is selected, the port is active
but audio is not embedded in the video

HDCP LED
 
ON: 
1
4
5
3
2
USB
Autoselect
SHOW
ME
AUDIO
SELECT
VIDEO
SELECT
VIDEO VIDEO VIDEO
AUDIO
AUDIO
AUDIO
VIDEO
AUDIO
HDCP
AUDIO1
DP
IN
DVI-D IN
RST
AUDIO2
A
U
D
I
O
1
I
N
HDMI2 IN
HDMI1 IN
1
4
5
3
2
USB
Autoselect
SHOW
ME
AUDIO
SELECT
VIDEO
SELECT
VIDEO
VIDEO
VIDEO
AUDIO AUDIO AUDIO
VIDEO
AUDIO
HDCP
AUDIO1
DP
IN
DVI-D IN
RST
AUDIO2
A
U
D
I
O
1
I
N
HDMI2 IN
HDMI1 IN
1
4
5
3
2
USB
Autoselect
SHOW
ME
AUDIO
SELECT
VIDEO
SELECT
VIDEO
VIDEO
VIDEO
AUDIO
AUDIO
AUDIO
VIDEO
AUDIO
HDCP
AUDIO1
DP
IN
DVI-D IN
RST
AUDIO2
A
U
D
I
O
1
I
N
HDMI2 IN
HDMI1 IN
USB LED
HDMI-3D-OPT-TX210A
 USB is disconnected or there is no USB data
transfer over the port.
 USB connection is established between the
transmitter and the computer.

 USB is disconnected or there is no USB data
transfer over the port.
 
 
Autoselect LED
 Autoselect function is disabled.
BLINKING: Autoselect function is enabled, searching for
signal (the video input LEDs are also blinking).
ON: Autoselect function is enabled, the active video signal
is found (the selected video input's LED is also ON).

Video Select Button
        
selected by the Video Select button from the front panel. The selection
order of the inputs is the following:
SW4-OPT-TX240RAK:
DP
HDMI 1
HDMI 2
Autoselect
DVI-D
1
4
5
3
2
USB
Autoselect
SHOW
ME
AUDIO
SELECT
VIDEO
SELECT
VIDEO
VIDEO
VIDEO
AUDIO
AUDIO
AUDIO
VIDEO
AUDIO
HDCP
AUDIO1
DP
IN
DVI-D IN
RST
AUDIO2
A
U
D
I
O
1
I
N
HDMI2 IN
HDMI1 IN
1
4
5
3
2
USB
Autoselect
SHOW
ME
AUDIO
SELECT
VIDEO
SELECT
VIDEO
VIDEO
VIDEO
AUDIO
AUDIO
AUDIO
VIDEO
AUDIO
HDCP
AUDIO1
DP
IN
DVI-D IN
RST
AUDIO2
A
U
D
I
O
1
I
N
HDMI2 IN
HDMI1 IN
1
4
5
3
2
USB
Autoselect
SHOW
ME
AUDIO
SELECT
VIDEO
SELECT
VIDEO
VIDEO
VIDEO
AUDIO
AUDIO
AUDIO
VIDEO
AUDIO
HDCP
AUDIO1
DP
IN
DVI-D IN
RST
AUDIO2
A
U
D
I
O
1
I
N
HDMI2 IN
HDMI1 IN



