What to do if MICROPOINT Blood Glucose Meter shows low battery?
If your MICROPOINT Blood Glucose Meter displays a low battery warning, replace the batteries or connect the meter to a power adapter. Also, turn off the meter and allow it to reach ambient temperature (10-35°C) for at least 5 minutes before further testing. Ensure the meter and strip are within the operational temperature range of 10°C to 35°C before retesting.
What to do if MICROPOINT Blood Glucose Meter says insufficient blood?
If you get this error with your MICROPOINT Blood Glucose Meter, retest using a new strip. Ensure that you add a minimum of 10 micro liters of blood correctly into the sample well.
What to do if the MICROPOINT qLabs ElectroMeter Medical Equipment says the HCT of the sample is out of range?
If your MICROPOINT Medical Equipment indicates that the HCT value of the sample is out of range, make sure that the HCT value of the sample is between 30% and 55%.
What should I do if the MICROPOINT qLabs ElectroMeter says that the strip is inserted inversely?
When inserting the test strip into the MICROPOINT Medical Equipment, make sure the test strip is facing up.
Why does the MICROPOINT qLabs ElectroMeter Medical Equipment say the ambient temperature is too high or too low?
Make sure that you use the MICROPOINT Medical Equipment in an environment with a temperature between 10 ° C and 35 ° C.
What should I do if the MICROPOINT qLabs ElectroMeter Medical Equipment says that the meter is vibrated?
Do not move, vibrate, or shake the MICROPOINT Medical Equipment during the test. Ensure that the meter is used in an environment away from high-frequency vibrations.
What to do if the MICROPOINT Medical Equipment shows low battery?
If your MICROPOINT Medical Equipment displays a low battery warning, use the power adapter or the base as a power source.
What to do if the MICROPOINT qLabs ElectroMeter displays 'FIB calculation error'?
If your MICROPOINT Medical Equipment displays a FIB calculation error, retest with a new test strip. If the problem recurs, contact your local dealer and use the laboratory method to perform the test.
What should I do if the MICROPOINT qLabs ElectroMeter Medical Equipment says 'no sample coagulation is detected'?
If the MICROPOINT Medical Equipment indicates that no sample coagulation is detected, retest with a new test strip. If the issue continues, contact your local dealer to perform the test using a laboratory method.
What to do if the MICROPOINT qLabs ElectroMeter displays 'APTT calculation error'?
If your MICROPOINT Medical Equipment displays an APTT calculation error, retest with a new test strip. If the problem persists, contact your local dealer and use the laboratory method to perform the test.
Instructions to read the manual before using the device.
Purpose of the qLabs monitoring system for quantitative measurement.
How the qLabs ElectroMeter detects coagulation and determines results.
Information on how the qLabs ElectroMeter is packed and storage advice.
Guidelines for handling, storing, and maintaining the qLabs ElectroMeter.
Importance of considering patient health for accurate test interpretation.
Instructions and precautions for operating the qLabs ElectroMeter during a test.
Steps for properly collecting a fingerstick blood sample for testing.
Procedures for collecting venous blood samples for the qLabs system.
Information on EMC compliance and potential interference.
Steps to turn on the qLabs ElectroMeter and initial setup.
Procedures for turning off the qLabs ElectroMeter and auto-shutdown.
How to access the main settings menu on the qLabs ElectroMeter.
How to select the desired language for the qLabs ElectroMeter interface.
Instructions for enabling, disabling, and connecting the qLabs ElectroMeter via Bluetooth.
How to configure test parameters like Sample No., Codechip, and Reference Range.
Configuration of system parameters like Date/Time, Beeper, and Screen Rotation.
Viewing device information such as version and system log.
Setting up and managing operator identification and password on the meter.
Entering the sample number for a test, manually or automatically.
How to correctly insert a test strip into the qLabs ElectroMeter.
Entering the Codechip number for the inserted test strip.
Installing the test strip Codechip into the meter's chip slot.
The meter enters a heating state before sample addition.
Instructions for adding the blood sample to the test strip.
Initiating and monitoring the test after sample addition.
Displaying and interpreting the PT/INR and APTT test results.
Inserting a test strip for quality control testing.
Entering Codechip information for the QC test strip.
Installing the Codechip for the QC test strip into the meter.
Entering the Codechip number for the QC liquid.
Installing the Codechip for the QC liquid into the meter.
The meter enters the heating state for QC testing.
Adding QC liquid sample to the test strip.
Performing the quality control test with the QC liquid.
Displaying and interpreting the results of the quality control test.
Accessing the results query screen to view test and QC results.
Viewing detailed information of individual test results.
Viewing detailed information of individual QC results.
Instructions and frequency for cleaning the qLabs ElectroMeter.
Recommended cleaning solutions and cloths for the qLabs ElectroMeter.
Step-by-step guide for cleaning and disinfecting the meter's exterior.
Safety precautions and charging advice for the device's lithium-ion battery.
Information on servicing and repair of the qLabs ElectroMeter.
Environmental conditions required for operating the qLabs ElectroMeter.
Technical specifications of the qLabs ElectroMeter, including processor, display, and power.
Terms and conditions of the limited two-year warranty for the qLabs ElectroMeter.
General| Sample Volume | 10 μL |
|---|---|
| Operating Temperature | 10°C to 40°C |
| Connectivity | USB |
| Dimensions | 120 x 65 x 25 mm |
| Weight | 150 g |
| Display | LCD |
| Sample Type | Whole blood |
| Measuring Range (PT/INR) | 0.8 - 8.0 INR |
| Storage Temperature (Test Strips) | 2°C to 30°C |
| Measurement Range | 0.8 - 8.0 INR |
| Input Impedance | Not Applicable |
| Storage Temperature | Not Applicable |
| Power Supply | 2 x AAA batteries |
To Next Page
