What does it mean if the MICROPOINT qLabs ElectroMeter displays 'External QC failed'?
If your MICROPOINT Medical Equipment displays 'External QC failed', ensure that the test strip and control are within their expiry period. Also, verify that you have entered the correct test strip Codechip number and control Codechip number.
What to do if the MICROPOINT qLabs ElectroMeter displays 'Internal QC failed'?
If your MICROPOINT Medical Equipment shows that the internal QC failed, use an unexpired test strip and enter the correct test strip Codechip number.
What to do if the MICROPOINT qLabs ElectroMeter Medical Equipment says the sample is insufficient?
If your MICROPOINT Medical Equipment indicates that the added sample is insufficient, retest with a new test strip, making sure to add enough blood for the test.
Why does the MICROPOINT Medical Equipment say the sample may not be suitable for qLabs testing?
If the MICROPOINT Medical Equipment indicates that the sample may not be suitable for qLabs testing, retest with a new test strip. If the problem continues, contact your local dealer and consider using a laboratory method for the test.
What to do if the MICROPOINT qLabs ElectroMeter says the sample adding has timed out?
Ensure that the sample adding is completed before the end of the countdown on your MICROPOINT Medical Equipment.
What should I do if the MICROPOINT qLabs ElectroMeter Medical Equipment says the sample is added too early?
If the MICROPOINT Medical Equipment indicates that the sample was added too early, use a new test strip and add the sample only after the meter prompts you to do so.
What to do if the MICROPOINT Medical Equipment shows a print error?
If your MICROPOINT Medical Equipment displays a print error, ensure that the meter is properly communicating with the base. Also, check that the printing paper at the base is installed correctly and that there is sufficient paper.
What to do if the MICROPOINT qLabs ElectroMeter displays 'Codechip reading error'?
If your MICROPOINT Medical Equipment shows a Codechip reading error, unplug the Codechip and reinsert it, ensuring it is fully inserted. If the problem continues, contact technical support.
What to do if heating has timed out on MICROPOINT qLabs ElectroMeter Medical Equipment?
If the heating process times out on your MICROPOINT Medical Equipment, adjust the ambient temperature to between 10 °C and 35 °C. Turn off the meter for 5 minutes, then turn it back on and restart the test. If the problem continues, contact technical staff.
What should I do if the MICROPOINT Medical Equipment is showing a Bluetooth error?
If your MICROPOINT Medical Equipment shows a Bluetooth error, turn the meter off and reboot it. If the problem persists, please contact technical support.
Instructions to read the manual before using the device.
Purpose of the qLabs monitoring system for quantitative measurement.
How the qLabs ElectroMeter detects coagulation and determines results.
Information on how the qLabs ElectroMeter is packed and storage advice.
Guidelines for handling, storing, and maintaining the qLabs ElectroMeter.
Importance of considering patient health for accurate test interpretation.
Instructions and precautions for operating the qLabs ElectroMeter during a test.
Steps for properly collecting a fingerstick blood sample for testing.
Procedures for collecting venous blood samples for the qLabs system.
Information on EMC compliance and potential interference.
Steps to turn on the qLabs ElectroMeter and initial setup.
Procedures for turning off the qLabs ElectroMeter and auto-shutdown.
How to access the main settings menu on the qLabs ElectroMeter.
How to select the desired language for the qLabs ElectroMeter interface.
Instructions for enabling, disabling, and connecting the qLabs ElectroMeter via Bluetooth.
How to configure test parameters like Sample No., Codechip, and Reference Range.
Configuration of system parameters like Date/Time, Beeper, and Screen Rotation.
Viewing device information such as version and system log.
Setting up and managing operator identification and password on the meter.
Entering the sample number for a test, manually or automatically.
How to correctly insert a test strip into the qLabs ElectroMeter.
Entering the Codechip number for the inserted test strip.
Installing the test strip Codechip into the meter's chip slot.
The meter enters a heating state before sample addition.
Instructions for adding the blood sample to the test strip.
Initiating and monitoring the test after sample addition.
Displaying and interpreting the PT/INR and APTT test results.
Inserting a test strip for quality control testing.
Entering Codechip information for the QC test strip.
Installing the Codechip for the QC test strip into the meter.
Entering the Codechip number for the QC liquid.
Installing the Codechip for the QC liquid into the meter.
The meter enters the heating state for QC testing.
Adding QC liquid sample to the test strip.
Performing the quality control test with the QC liquid.
Displaying and interpreting the results of the quality control test.
Accessing the results query screen to view test and QC results.
Viewing detailed information of individual test results.
Viewing detailed information of individual QC results.
Instructions and frequency for cleaning the qLabs ElectroMeter.
Recommended cleaning solutions and cloths for the qLabs ElectroMeter.
Step-by-step guide for cleaning and disinfecting the meter's exterior.
Safety precautions and charging advice for the device's lithium-ion battery.
Information on servicing and repair of the qLabs ElectroMeter.
Environmental conditions required for operating the qLabs ElectroMeter.
Technical specifications of the qLabs ElectroMeter, including processor, display, and power.
Terms and conditions of the limited two-year warranty for the qLabs ElectroMeter.
General| Sample Volume | 10 μL |
|---|---|
| Operating Temperature | 10°C to 40°C |
| Connectivity | USB |
| Dimensions | 120 x 65 x 25 mm |
| Weight | 150 g |
| Display | LCD |
| Sample Type | Whole blood |
| Measuring Range (PT/INR) | 0.8 - 8.0 INR |
| Storage Temperature (Test Strips) | 2°C to 30°C |
| Measurement Range | 0.8 - 8.0 INR |
| Input Impedance | Not Applicable |
| Storage Temperature | Not Applicable |
| Power Supply | 2 x AAA batteries |
To Next Page
