Miele G2000 - Page 33

To Next Page

To Previous Page

Technical Information

G1000 / G2000 Dishwashers

Figure 4-4: Water Inlet Mixer

Main Page

Table of Contents2
Warnings and Safety Information10
Construction and Design11
Appliance Overview11
Appliance Overview - Typical Integrated Model11
Appliance Overview - Typical Fully Integrated Model12
Controls Overview13
Types of Dishwashers14
Pre-Finished14
Integrated14
Fully Integrated14
Technical Data15
Electrical Information15
Plumbing Connections16
Intake Connection16
Drain Connection16
Dimensions16
Data Tag17
Data Tag - Location18
Data Tag - Information18
Model Numbering18
Mode Numbering - Overview of USA Model Numbers19
Door Springs / Weights - Specifications20
Layout of Components (Typical)21
Installation22
Commission and Operation23
Door Handle / Lock - Prefinished & Integrated Models23
Child Safety Lock23
Water Softener24
Water Softener Salt - General Information24
Water Softener Salt - Adding24
General Operation26
Novotronic Controls26
Touchtronic & Navitronic Controls26
Fully Integrated (Incognito) (VI) Controls27
Description of Function29
Cabinet Construction29
Water Intake30
Waterproof System (WPS)30
Water Inlet Mixer32
Water Inlet Mixer Without EGS35
Water Inlet Mixer Wth EGS36
Water Inlet Mixer During Reactivation37
Flow Meter B3/4, Water Intake Quantity38
Sensor Softener38
Electronically Controlled Water Hardness (EGS)39
Intelligent Tab Function39
Water Circulation & Heating41
Circulation Pump42
Circulation Pump - Speed Sensor and Load Sensing43
Heating45
NTC Temperature Sensor, R3045
Heater Pressure Switch, B1/1347
Turbidity Sensor (ECO Sensor III, Auto-Sensor), B3/1048
Spray Arm Sensing50
Filter Combination with Micro Fine Filter51
Dispensing52
Combination Dispenser52
Drain System53
Drain Pump53
Drying54
Circulation Turbothermic Drying (Active): UTT Version 154
Circulation Turbothermic Drying (Active): UTT Version 256
Fan57
Service and Maintenance58
Housing58
Side Panel - Removal59
Drip Pan - Removal59
Door61
Front Panel (GDU / Custom) - Removal61
Door Tension - Adjustment62
Outer Door Panel - Removal64
Fascia Panel Removal65
Door Hinge - Removal65
Combination Dispenser Unit - Removal67
Cable Holder - Removal68
Bottom Door Seal - Removal68
Locking Plate - Adjustment69
Door Lock - Removal (Integrate Models)70
Door Switch - Replacement (Integrated Models)71
Fully Integrated (VI) Lock with Door Contact Switch Removal72
Door Lock Emergency Release - Activate (Fully Integrated)72
Inner Cabinet73
Door Seal - Replacement73
Toe Kick (Plinth Removal)74
Cover Plate - Removal75
Connecting Strip (Lower Support) - Removal76
Multi-Plinth Removal (Door Tension Spring Housing)77
Steam Condenser Removal78
Fan Removal78
Basket Runners - Removal79
Water Level Check80
Waterproof System (WPS) Restrictor - Replacement82
Waterproof System (WPS) - Removal83
Flowmeter (Circuit Board) - Removal84
Top Spray Arm Removal84
Middle Spray Arm Removal84
Bottom Spray Arm Removal85
Feed Pipe with Turbidity Sensor - Top Spray Arm, Removal85
Feed Pipe - Middle Spray Arm, Removal85
Spray Arm Sensor Removal85
Water Inlet Mixer with Resin Chamber - Removal86
EGS Valve Solenoid - Removal88
Reactivation Valve - Removal88
Salt Container - Removal89
Circulation Pump - Removal89
Circulation Pump - Service91
Pump Cap Removal / Heater Element - Access92
Slide Shutter Removal92
Drive Removal93
Pump Impeller Removal95
Pump Housing Removal95
Capacitor Removal95
Heater Pressure Switch Removal95
Speed Sensor Removal95
Drain Pump Removal96
Float Switch Removal96
Sump Removal97
NTC Temperature Sensor Removal98
Filter Combination Dismantling99
Filter Combination Assembly (New Micro Fine Filter and Handle)100
Filter Combination Assembly (with Locking Piece)101
Electronic Unit103
Mains Switch Removal (Integrated)104
Electronic Unit Holder Removal105
Electronic Unit Removal (Integrated)105
Fault Diagnosis106
Diagnostic Modes - Overview106
Water Hardness Setting - Checking and Programming107
Advanta Series107
Advanta Series - G2020107
G2020 - Programming Mode107
G2020 - Service Mode112
G2020 Component Test - Information115
Advanta Series - G2170117
G2170 - Programming Mode117
G2170 - Service Mode124
G2170 Component Test - Information127
Inspira Series129
Inspira Series - G2140 & G2150129
G2140 / G2150 - Programming Mode129
G2140 / G2150 Service Mode134
G2140 / G2150 Component Test - Information137
Inspira Series - G1180 & G2180139
G1180 / G2180 - Programming Mode139
G1180 / G2180 - Service Mode146
G1180 / G2180 - Component Test149
Optima Series151
Optima Series - G2420 & G2430151
G2420 / G2430 - Programming Mode151
G2420 / G2430 - Service Mode Summary157
G2420 / G2430 Component Test160
Optima Series - G1470 & G2470162
G1470 / G2470 Programming Mode162
G1470 / G2470 - Service Mode168
G1470 / G2470 Component Test170
Excella Series172
Excella Series - G2630172
G2630 Programming Mode172
G2630 - Service Mode178
G2630 Component Test180
Excella Series - G2670183
G2670 Programming Mode183
G2670 - Service Mode187
G2670 Component Test189
Laperla - G2830192
G2830 - Program Mode192
G2830 - Service Mode197
G2830 Component Test199
Fault Code Summary203
Fault Repair Summary204
No Power - Main Switch Is on204
Display Shows "Close Salt Reservoir Cap204
Drain Pump Switches on and off at Short Intervals204
Inlet / Drain LED Flashes and Lights up Alternately (Fully Integrated)205
Dishwasher Program Can be Selected but Not Started205
Dishwashing Program Interrupted, no Fault Indication205
Door Does Not Close Correctly206
Condensation Forms on Adjacent Cabinets206
Noises During Drying Cycle207
Foreign Object in Drain System207
Poor Drying Results208
No Drying or Drying too Slow208
Water Present in Appliance and Is Not Being Drained off210
Inlet/Drain LED Flashes During Water Intake, Dishwasher Ends Selected Program. (F12, F13 or F19)211
Wash Program Is Interrupted and Drain Pump Is Operated214
The Program Is Not Interrupted, but Faults Are Logged into the Fault Memory220

Miele G2000 - Page 33

Table of Contents

Related product manuals