Mitsubishi Electric MELSEC iQ-R-R00CPU - Page 867

APPX
Appendix 5 List of Special Register Areas
865
A
SD1364 Target setting for iQ
Sensor Solution data
backup/restoration
(target module)
Target setting for data
backup/restoration
(target module)
Set the target module of the iQ Sensor Solution data backup/
restoration.
I/O number.
*1
: Module
3FFH: Built-in Ethernet
*2
URn
*3
SD1365 Target setting for iQ
Sensor Solution data
backup/restoration
(target device 1)
Target setting for data
backup/restoration
(target device 1)
Set the target device of the iQ Sensor Solution data backup/
restoration.
<AnyWireASLINK>
ID number
<CC-Link and CC-Link IE Field Network>
Station number
<Ethernet>
IP address (lower 16 bits)
Example: When the IP address is 192.168.3.40, 3 = 3H and 40 =
28H. Therefore, the value of lower 16 bits (0328H) is 808.
URn
*3
SD1366 Target setting for iQ
Sensor Solution data
backup/restoration
(target device 2)
Target setting for data
backup/restoration
(target device 2)
Set the target device of the iQ Sensor Solution data backup/
restoration.
<AnyWireASLINK>
0 (Not used)
<CC-Link and CC-Link IE Field Network>
Station sub-ID number
<Ethernet>
IP address (upper 16 bits)
Example: When the IP address is 192.168.3.40, 192 = C0H and
168 = A8H. Therefore, the value of upper 16 bits (C0A8H) is 49320.
URn
*3
SD1367 Operation setting for
iQ Sensor Solution
data backup/
restoration
Operation setting for
data backup/
restoration.
Set the operation of the iQ Sensor Solution data backup/
restoration.
b0 to b7: Operation setting at error occurrence (0: Continue, 1:
Stop)
b8 to b15: Fixed to 0
URn
*3
SD1371 Execution status of iQ
Sensor Solution data
backup/restoration
(total number of target
devices)
Execution status of
data backup/
restoration (total
number of target
devices)
• This register stores the total number of target devices of the data
backup/restoration of iQ Sensor Solution for each execution unit.
• This register is cleared to 0 when the right to use is acquired or
the backup/restoration is requested.
S (Status
change)
Rn
*3
SD1372 Execution status of iQ
Sensor Solution data
backup/restoration
(normal completion
count)
Execution status of
data backup/
restoration (normal
completion count)
• This register indicates the execution status (the number of
devices where the processing has been completed normally) of
the iQ Sensor Solution data backup/restoration.
• Among the devices where the operation has been completed, the
number of devices where the operation has been completed
normally is stored.
• This register is cleared to 0 when the right to use is acquired or
the backup/restoration is requested.
S (Status
change)
Rn
*3
SD1373 Execution status of iQ
Sensor Solution data
backup/restoration
(error completion
count)
Execution status of
data backup/
restoration (error
completion count)
• This register indicates the execution status (the number of
devices where the processing has been completed with an error)
of the iQ Sensor Solution data backup/restoration.
• Among the devices where the operation has been completed, the
number of devices where the operation has been completed with
an error is stored.
• This register is cleared to 0 when the right to use is acquired or
the backup/restoration is requested.
S (Status
change)
Rn
*3
SD1374 Execution status of iQ
Sensor Solution data
backup/restoration
(progress per device)
Execution status of
data backup/
restoration (progress
per device)
• This register indicates the progression status of the iQ Sensor
Solution data backup/restoration of the device in progress in
percentage (0 to 100%).
Range of the value: 0 to 100 (%)
• This register is cleared to 0 when the right to use is acquired or
the backup/restoration is requested.
S (Status
change)
Rn
*3
SD1375 Folder number of iQ
Sensor Solution data
backup
Backup target folder
number
• This register stores a number of the target folder where the
backup data of the device supporting iQSS is stored.
0 to 99: Folder number
FFFFH: Backup data not saved
• This register stores FFFFH when the right to use is acquired or
the backup/restoration is requested.
S (Status
change)
Rn
*3
No. Name Data stored Details Set by
(setting
timing)
CPU
b15 b7b8
b0