Mitsubishi Electric R60AD8-G

To Next Page

To Previous Page

14 TROUBLESHOOTING

14.2 Checking the State of the Module

307

Module Information List

Switch to the "Module Information List" tab to display each status information of the R60AD8-G.

Item Description

LED information Displays the LED status of the R60AD8-G.

Main Page

Default Chapter3
- Safety Precautions3
- Conditions of Use for the Product11
- Introduction12
- Table of Contents13
- Relevant Manuals17
- Terms17
- Part 1 Standard Mode19
Chapter 1 Functions20
- Processing of each Function21
- Range Switching Function22
- A/D Conversion Enable/Disable Setting Function23
- A/D Conversion Method24
- Scaling Function28
- Alert Output Function32
  - Process Alarm32
  - Rate Alarm35
- Input Signal Error Detection Function40
  - When the Function Is Used in the Q Compatible Mode48
- Shift Function53
- Digital Clipping Function56
- Difference Conversion Function58
- Maximum Value/Minimum Value Hold Function62
- Logging Function63
- Interrupt Function83
- Error History Function86
- Event History Function89
- Backing Up, Saving, and Restoring Offset/Gain Values90
  - When the Module-Specific Backup Parameter Is Used90
  - When the Module-Specific Backup Parameter Is Not Used93
- Q Compatible Mode Function97
Chapter 2 Parameter Settings98
- Basic Setting98
- Application Setting99
- Interrupt Setting100
- Refresh Setting101
  - Refresh Processing Time102
Chapter 3 Troubleshooting103
- 3.1 Troubleshooting with the Leds103
- Checking the State of the Module104
- Troubleshooting by Symptom106
- List of Error Codes110
- List of Alarm Codes114
- Appendices (Standard Mode)115
Appendix 1 Module Label115
Appendix 2 I/O Signals117
- List of I/O Signals117
- Details of Input Signals118
- Details of Output Signals125
Appendix 3 Buffer Memory Areas127
- List of Buffer Memory Addresses127
- Details of Buffer Memory Addresses148
Appendix 4 Dedicated Instructions207
- Instruction List207
Appendix 5 Operation Examples of When the Remote Head Module Is Mounted208
- System Configuration Example208
- Setting in the Master Station209
- Setting in the Intelligent Device Station212
- Checking the Network Status216
- Program Examples216
Appendix 6 Disabling the Safety Module219
Appendix 7 Added or Modified Function220
- Part 2 Sil2 Mode221
Chapter 4 Overview222
Chapter 5 Part Names225
Chapter 6 Specifications227
- Performance Specifications227
- Function List229
Chapter 7 Procedures before Operation230
Chapter 8 System Configuration237
- Redundant Master Station238
- Redundant Line240
- Firmware Version for SIL2 Mode242
- Reference Product242
Chapter 9 Installation and Wiring243
- Wiring Precautions243
  - Connector for External Devices243
- External Wiring244
Chapter 10 Functions251
- SIL2 Mode252
- Processing of each Function266
- Range Switching Function267
- A/D Conversion Enable/Disable Setting Function268
- A/D Conversion Method268
- Scaling Function271
- Digital Clipping Function274
- SIL2 A/D Conversion Function276
- Self-Diagnostic Function292
- Error History Function293
- Event History Function294
Chapter 11 Parameter Settings296
- Basic Settings296
- Application Settings297
- Refresh Settings298
Chapter 12 Example of Operation299
Chapter 13 Maintenance and Inspection305
Chapter 14 Troubleshooting307
- Troubleshooting with the Leds307
- Checking the State of the Module308
- Troubleshooting by Symptom310
- Troubleshooting While Proceeding Procedures before Operation315
- Troubleshooting SIL2 Diagnostic FB Library318
- List of Error Codes322
- Appendices (Sil2 Mode)325
Appendix 8 I/O Signals325
- List of I/O Signals325
Appendix 9 Buffer Memory326
- List of Buffer Memory Addresses326
- Details of Buffer Memory Area326
Appendix 10I/O Conversion Characteristics327
Appendix 11 Accuracy330
Appendix 12Calculation Method of Safety Response Time (Maximum Value)331
Appendix 13Added or Modified Function332
Appendix 14External Dimensions333
- Index334
- Revisions336
- Warranty337
- Trademarks340

Mitsubishi Electric R60AD8-G - Page 309

Table of Contents

Related product manuals