Mobatime DC.57.4 - Control PCB Layout and Functions

52 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

© MOBATIME 11 / 52 800693.16

2.6 Control PCB

Table of Contents

Default Chapter3
- Table of Contents3
1 Description5
2 Assembly7
- Single-Sided Clock7
- Double-Sided Clock8
- Dismantling of the Clock Rear Cover9
- Assembly Diagram10
- Connecting Terminal Block10
- Control PCB11
- Function of the Plug Connectors12
- Setting Elements12
- Connection of the Cable Ends13
3 Control of the Clock Using Keyboard or Pushbuttons14
- Setting of Time and Date14
- Menu for the Setting of the Clock Parameters15
4 Control of the Clock Using IR Remote Control19
- Setting of Time and Date19
- Menu for the Setting of the Clock Parameters20
5 The Clock Menu Table24
- Ipv6 Adress Submenu26
6 Control of the Stopwatch Via Keyboard27
- The Stopwatch Menu27
- Setting of the Initial Time for Counting down27
7 Control of the Stopwatch Using IR Remote Control28
- The Stopwatch Menu28
- Setting of Initial Time for Counting down29
- Switching Contact29
8 Stopwatch Menu Table30
9 Local Time Calculation32
- Basic Setting - Control According to Source of Synchronization32
- Calculation Using Mobaline Time Zones32
- Calculation Using Time Zone Server MOBATIME32
- Calculation Using Time Zone Entries Preconfigured by MOBA-NMS Software33
- Calculation According to Internal Time Zone Table33
10 Non-Network Clock Operation34
- Autonomous Clock Synchronized by DCF 77 Receiver34
- Autonomous Clock Synchronized by GPS Receiver34
- Slave Clock Controlled by Synchronizing Impulses34
  - Synchronization and Time Setting - P5 Mode 1 and 335
  - Synchronization Only - P5 Mode 2 and 435
- Slave Clock Controlled by MOBATIME Serial Code, Mobaline, or IRIG-B35
- Slave Clock Controlled by IF482 over RS232 or RS48535
- Slave Clock Controlled by Supervised RS48536
- Cascaded Connection of the DCF/GPS Synchronized Clock36
- Synchronization in WTD System36
- Connecting the Slave Displays through RS48536
11 NTP and Poe Clock Operation37
- Unicast Mode37
- Multicast Mode40
12 Wifi Clock Operation41
- Setting Via Default MOBA-WIFI Wireless Network (Configure Using)41
- Setting Via AP Mode (Configure Using)41
  - Wifi Version41
  - Wifi 2.4/5 Ghz Version42
- Setting the Network Parameters Using Telnet42
13 Testing Mode, Parameter Reset44
- Synchronization Test44
- Parameter Reset44
14 Firmware Update45
- Firmware Update Using RS23245
- Firmware Update over Ethernet on NTP and Poe Versions45
15 Time Zone Table46
16 Engineering Data48
- Standard Design of the Clock48
- Voltage Range and Electric Current Consumption of the Lines48
17 Accessories and Maintenanc49
- Single-Sided Clock49
- Double-Sided Clock49
18 Cleaning49
19 Disposal of Used Batteries49
20 Guarantee and Maintenance49

Related product manuals

Mobatime DC.57.6

Preview: Mobatime DC Series

Mobatime DC Series

Mobatime DTS 4135.timeserver

Preview: Mobatime DTS 4801.masterclock

Mobatime DTS 4801.masterclock

Mobatime DTS 4802.masterclock

Preview: Mobatime PROFILINE Series

Mobatime PROFILINE Series

Preview: Mobatime EuroTime Center ETC 12

Mobatime EuroTime Center ETC 12

Mobatime EuroTime Center ETC 24R