NETGEAR GS908E User Manual

12. Restore your computer to its original IP address.
13. Verify that you can connect to the switch with its new IP address:
a. Open a web browser from a computer that is connected to the same network as the switch.
b. Enter the new IP address that you assigned to the switch.
The login page displays.
c. Enter the switch password.
The default password is password. The password is case-sensitive.
The HOME page displays.
Use the NETGEAR Insight App to Access the Switch
The NETGEAR Insight app lets you discover the switch in your network and access the local browser
interface of the switch from your smartphone.
To access the switch from the Insight app:
1. On your iOS or Android mobile device, go to the app store, search for NETGEAR Insight, and download
and install the app.
2. If the switch is directly connected to a WiFi router or access point, connect your mobile device to the
WiFi network of the router or access point.
3. Select LOG IN to log in to your existing NETGEAR account or tap the CREATE NETGEAR ACCOUNT
button to create a new account.
4. After you log in to your account, name your network and specify a device admin password that applies
to all devices that you add to this network, and tap the NEXT button.
5. You can now add a device. Choose one of the following options:
• Add a device by scanning your network.
• Add a device by entering its serial number.
• Add a device by scanning its barcode.
Pages might display and suggest that you connect the switch to power and to an
uplink. If you already did this, on these pages, tap the NEXT button.
Note
6. If the switch is not yet connected to the same WiFi network as your mobile device, connect it now to the
same WiFi network, wait two minutes, and then tap the NEXT button.
The switch is discovered and registered on the network.
7. In the Insight app, select the switch and tap the Visit Web Interface link.
The login page of the local browser interface opens.
8. Enter the switch password.
The default password is password. The password is case-sensitive.
The HOME page displays.
Install and Access the Switch in Your Network
18
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS908E

NETGEAR GS908E Specifications

General

Switch type	Managed
Quality of Service (QoS) support	Yes
Safety	IEC 60950-1:2005(ed.2) + A1:2009 + A2:2013, UL 60950-1, CAN/CSA C22.2 No. 60960-1-07, EN 60950-1: 2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013, IEC 60950-1:2005 (ed.2)+A1:2009+A2:2013, AS/NZS 60950.1:2015
Stackable	-
Certification	47 CFR FCC Part 15, ICES-003:2016, ANSI C63.4:2014, EN 55022:2010 + AC:2011, EN 55024:2010, EN 61000-3-2:2014, EN 6100-3-3:2013, AS/NZS CISPR 22:2009 + A1:2010, VCCI V-3/2015.04, V-4/2012.4
Product color	Black, White
Rack mounting	No
Number of multicast groups filtered	128
USB 2.0 ports quantity	2
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	26.3 W
Power consumption (typical)	3.3 W
Number of VLANs	64
Networking standards	IEEE 802.1Q, IEEE 802.1p
Virtual LAN features	Port-based VLAN
DHCP features	DHCP client
Jumbo frames	9000
Forwarding rate	11.9 Mpps
Number of queues	4
MAC address table	4000 entries
Heat dissipation	89.8 BTU/h
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Harmonized System (HS) code	85176990

Weight and Dimensions

Depth	164 mm
Width	234 mm
Height	33 mm
Weight	370 g