NETGEAR GS908E User Manual

Chapter 4 Use VLANS for Traffic Segmentation
VLAN Overview....................................................................................................37
Manage Port-Based VLANs.................................................................................37
Activate the Port-Based VLAN Mode..............................................................37
Create a Port-Based VLAN.............................................................................38
Change a Port-Based VLAN............................................................................39
Delete a Port-Based VLAN..............................................................................40
Manage 802.1Q-Based VLANs............................................................................40
Activate the 802.1Q-Based VLAN Mode.........................................................40
Create an 802.1Q-Based VLAN......................................................................41
Change an 802.1Q-Based VLAN....................................................................42
Delete an 802.1Q-Based VLAN......................................................................43
Specify a Port PVID for an 802.1Q-Based VLAN............................................44
Set an Existing 802.1Q-Based VLAN as the Voice VLAN and Adjust the CoS
Value...............................................................................................................45
Change the OUI Table for the Voice VLAN......................................................46
Deactivate the Port-Based or 802.1Q-Based VLAN Mode and Delete All VLANs.47
Chapter 5 Manage the Switch in Your Network
Manage Switch Discovery Protocols....................................................................49
Manage Universal Plug and Play....................................................................49
Manage Bonjour..............................................................................................49
Manage NETGEAR Switch Discovery Protocol..............................................50
Manage Multicast.................................................................................................51
Manage IGMP Snooping.................................................................................51
Enable a VLAN for IGMP Snooping................................................................52
Manage Blocking of Unknown Multicast Addresses........................................52
Manage IGMPv3 IP Header Validation............................................................53
Set Up a Static Router Port for IGMP Snooping.............................................54
Set Up Static Link Aggregation............................................................................54
Set Up One or More Link Aggregation Groups...............................................55
Make a Link Aggregation Connection.............................................................56
Enable One or More Link Aggregation Groups...............................................56
Change the IP Address of the Switch..................................................................57
Reenable the DHCP Client of the Switch.............................................................58
Chapter 6 Maintain and Monitor the Switch
Manually Check for New Switch Firmware and Update the Switch......................60
Manage the Configuration File.............................................................................61
Back Up the Switch Configuration...................................................................61
Restore the Switch Configuration....................................................................61
Return the Switch to Its Factory Default Settings.................................................62
Use the Reset Button to Reset the Switch......................................................62
Use the Local Browser Interface to Reset the Switch.....................................63
Manage the Power Saving Mode.........................................................................64
Control the LEDs..................................................................................................64
Change the Switch Device Name........................................................................65
4
8-Port Gigabit Ethernet Smart Managed Plus Switch Model GS908E

NETGEAR GS908E Specifications

General

Switch type	Managed
Quality of Service (QoS) support	Yes
Safety	IEC 60950-1:2005(ed.2) + A1:2009 + A2:2013, UL 60950-1, CAN/CSA C22.2 No. 60960-1-07, EN 60950-1: 2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013, IEC 60950-1:2005 (ed.2)+A1:2009+A2:2013, AS/NZS 60950.1:2015
Stackable	-
Certification	47 CFR FCC Part 15, ICES-003:2016, ANSI C63.4:2014, EN 55022:2010 + AC:2011, EN 55024:2010, EN 61000-3-2:2014, EN 6100-3-3:2013, AS/NZS CISPR 22:2009 + A1:2010, VCCI V-3/2015.04, V-4/2012.4
Product color	Black, White
Rack mounting	No
Number of multicast groups filtered	128
USB 2.0 ports quantity	2
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	26.3 W
Power consumption (typical)	3.3 W
Number of VLANs	64
Networking standards	IEEE 802.1Q, IEEE 802.1p
Virtual LAN features	Port-based VLAN
DHCP features	DHCP client
Jumbo frames	9000
Forwarding rate	11.9 Mpps
Number of queues	4
MAC address table	4000 entries
Heat dissipation	89.8 BTU/h
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Harmonized System (HS) code	85176990

Weight and Dimensions

Depth	164 mm
Width	234 mm
Height	33 mm
Weight	370 g