EasyManuals Logo

NETGEAR Nighthawk AC1900 D7000v2 User Manual

NETGEAR Nighthawk AC1900 D7000v2
215 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #206 background imageLoading...
Page #206 background image
Troubleshoot Internet Browsing
If your modem router can obtain an IP address but your computer is unable to load any web pages from the
Internet, it might be for one of the following reasons:
• The traffic meter is enabled, and the limit was reached.
By configuring the traffic meter not to block Internet access when the traffic limit is reached, you can
resume Internet access (see Unblock the Traffic Meter After the Traffic Limit Is Reached on page 175).
If your ISP sets a usage limit, they might charge you for the overage.
• Your computer might not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www addresses) to
numeric IP addresses.Typically your ISP provides the addresses of one or two DNS servers for your
use. If you entered a DNS address when you set up the modem router, reboot your computer and verify
the DNS address. Alternatively, you can configure your computer manually with DNS addresses, as
explained in your operating system documentation.
• The modem router might not be configured as the TCP/IP router on your computer.
For information about TCP/IP problems, see Troubleshoot Your Network Using the Ping Utility on page
207.
If your computer obtains its information from the modem router by DHCP, reboot the computer and
verify the modem router address.
Changes Are Not Saved
If the modem router does not save the changes that you make on a modem router web page, do the following:
• When entering configuration settings, always click the Apply button before moving to another page or
tab or your changes are lost.
• Click the Refresh or Reload button in the web browser. It is possible that the changes occurred but
that the old settings remain in the web browser’s cache.
Troubleshoot the WiFi Connectivity
If you are experiencing trouble connecting over WiFi to the modem router, try to isolate the problem:
• Make sure that the WiFi settings in your WiFi device and modem router match exactly.
For a device that is connected over WiFi, the WiFi network name (SSID) and WiFi security settings of
the modem router and WiFi computer must match exactly. The default SSID and password are on the
product label (see Label on page 16).
• Does the WiFi device that you are using find your WiFi network?
If not, check the WiFi LED on the top of the modem router. If this LED is off, both WiFi radios might
be disabled. For more information about the WiFi radios, see Control the WiFi Radios on page 87.
Troubleshooting
206
Nighthawk AC1900 WiFi VDSL/ADSL Modem Router Model D7000v2

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR Nighthawk AC1900 D7000v2 and is the answer not in the manual?

NETGEAR Nighthawk AC1900 D7000v2 Specifications

General IconGeneral
WiFi PerformanceAC1900 (600 + 1300 Mbps)
WiFi RangeLarge homes
Memory128 MB Flash and 256 MB RAM
Frequency Band2.4GHz and 5GHz
Beamforming+Yes
Smart ConnectYes
Guest NetworkYes
VPN SupportYes
Parental ControlsYes
Quality of Service (QoS)Yes
WiFi Technology802.11ac
Number of Ethernet Ports4 x Gigabit Ethernet
Number of USB Ports2 (USB 2.0 and USB 3.0)
ProcessorDual-core 1GHz
Security FeaturesWPA/WPA2
Wireless Standard802.11 a/b/g/n/ac
Ports4 Gigabit Ethernet, 2 USB
Modem TypeVDSL/ADSL

Related product manuals