Home
NETGEAR
Wireless Access Point
ProSafe WNAP320
NETGEAR ProSafe WNAP320 User Manual
4
of 1
of 1 rating
126 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Chapter 1. Introduction
|
13
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Bottom P
anel with Product Label
The product label on the bottom of
the wireless
access point’
s enclosure displays factory
default settings, regulatory co
mpliance, an
d other information:
Figure 3.
12
14
Table of Contents
Default Chapter
2
Revision History
2
Technical Support
2
Table of Contents
3
Chapter 1 Introduction
6
About the Prosafe Wireless-N Access Point WNAP320
6
What Is in the Box
7
System Requirements
7
Key Features and Standards
7
Supported Standards and Conventions
8
Key Features
8
802.11B/G/N Standards-Based Wireless Networking
10
Autosensing Ethernet Connections with Auto Uplink
10
Hardware Description
10
Top Panel
11
Rear Panel
12
Bottom Panel with Product Label
13
Chapter 2 Installation and Basic Configuration
14
What You Need before You Begin
14
Wireless Equipment Placement and Range Guidelines
14
Ethernet Cabling Requirements
15
LAN Configuration Requirements
15
Computer Hardware Requirements
15
Install and Configure the Wireless Access Point
16
Connect the Wireless Access Point to Computer
16
Log in to the Wireless Access Point
18
Configure Basic General System Settings and Time Settings
19
Configure IP Settings and Optional DHCP Server Settings
21
Configure Basic Wireless Settings
23
Test Basic Wireless Connectivity
27
Mount the Wireless Access Point
28
Ceiling Installation
28
Wall Installation
30
Desk Installation
33
Chapter 3 Wireless Configuration and Security
34
Wireless Data Security Options
34
Security Profiles
36
Before You Change the SSID, WEP, and WPA Settings
38
Configure and Enable Security Profiles
39
Configure RADIUS Server Settings
48
Restrict Wireless Access by MAC Address
50
Schedule the Wireless Radio
52
Configure Basic Wireless Quality of Service
52
Chapter 4 Management
55
Enable Remote Management
55
SNMP Management
56
Secure Shell and Telnet Management
57
Upgrade the Wireless Access Point Software
58
Manage the Configuration File or Reset to Factory Defaults
60
Save the Configuration
60
Restore the Configuration
61
Restore the Wireless Access Point to the Factory Default Settings
62
Reboot the Wireless Access Point Without Restoring the Default Configuration
63
Change the Administrator Password
64
Enable the Syslog Server
65
Monitor the Wireless Access Point
66
View System Information
66
Monitor Wireless Stations
68
View the Activity Log
70
Traffic Statistics
71
Enable Rogue AP Detection and Monitor Access Points
72
Enable and Configure Rogue AP Detection
72
View and Save Access Point Lists
74
Chapter 5 Advanced Configuration
76
Spanning Tree Protocol and 802.1Q VLAN
76
Hotspot Settings
78
Configure Advanced Wireless Settings
79
Configure Advanced Qos Settings
81
Configure Wireless Bridging
84
Configure a Point-To-Point Wireless Network
85
Configure a Point-To-Multipoint Wireless Network
88
Configure the Wireless Access Point for Repeater Mode
92
Configure the Wireless Access Point for Client Mode
96
Chapter 6 Troubleshooting
97
Basic Functioning
98
No Leds Are Lit on the Wireless Access Point
98
The Active LED or the LAN LED Is Not Lit
99
The WLAN LED Does Not Light up
99
You Cannot Access the Internet or the LAN from a Wireless-Capable Computer
99
You Cannot Configure the Wireless Access Point from a Browser
100
When You Enter a URL or IP Address a Time-Out Error Occurs
101
Troubleshooting a TCP/IP Network Using the Ping Utility
101
Testing the LAN Path to Your Wireless Access Point
101
Testing the Path from Your Computer to a Remote Device
102
Problems with Date and Time
103
Use the Packet Capture Tool
103
Appendix A Supplemental Information
105
Related Documents
105
Technical Specifications
106
Factory Default Settings
107
Appendix B Command-Line Reference
109
Telnet Connection
109
Appendix C Notification of Compliance
117
Regulatory Compliance Information
117
Fcc Radiation Exposure Statement
118
Industry Canada Statement
118
Index
121
Other manuals for NETGEAR ProSafe WNAP320
Specifications
3 pages
Installation Guide
2 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the NETGEAR ProSafe WNAP320 and is the answer not in the manual?
Ask a question
NETGEAR ProSafe WNAP320 Specifications
General
Brand
NETGEAR
Model
ProSafe WNAP320
Category
Wireless Access Point
Language
English
Related product manuals
NETGEAR ProSAFE WN203
133 pages
NETGEAR ProSafe WNDAP620
2 pages
WG302 - 802.11g ProSafe Wireless Access Point
128 pages
WG602 - 54 Mbps Wireless Access Point
122 pages
NETGEAR WAC104
94 pages
NETGEAR WAX214
152 pages
NETGEAR WAX630
270 pages
NETGEAR WAC510
232 pages
NETGEAR WAC124
263 pages
NETGEAR WAC730
113 pages
NETGEAR WAX206
7 pages
NETGEAR WiFi 6 AX1800
249 pages