Omega PLATINUM Series User Manual

PLATINUM
TM
Series Controllers User’s Guide
M5451 Omega Engineering | www.omega.com
5
Introduction
7.8.2 Select Program (PRoG > M.RMP > S.PRG) ........................................................................... 65
7.8.3 Multi-Ramp/Soak Tracking (PRoG > M.RMP > M.tRk) ........................................................ 65
7.8.4 Time Format (PRoG > M.RMP > tIM.F) ............................................................................... 65
7.8.5 Program End Action (PRoG > M.RMP > E.ACT) ................................................................... 66
7.8.6 Number of Segments (PRoG > M.RMP > N.SEG) ................................................................. 66
7.8.7 Segment Number for Editing (PRoG > M.RMP > S.SEG) ..................................................... 66
7.8.8 More on Multi-Ramp/Soak Programming .......................................................................... 67
8. Reference Section: Operating Mode (oPER) ....................................................................................... 69
8.1 Normal Run Mode (oPER > RUN) ................................................................................................ 69
8.2 Change Setpoint 1 (oPER > SP1) .................................................................................................. 69
8.3 Change Setpoint 2 (oPER > SP2) .................................................................................................. 70
8.4 Manual Mode (oPER > MANL) .................................................................................................... 70
8.5 Pause Mode (oPER > PAUS) ........................................................................................................ 71
8.6 Stop Process (oPER > StoP) ......................................................................................................... 71
8.7 Clear Latched Alarms (oPER > L.RSt) ........................................................................................... 71
8.8 Display Valley Reading (oPER > VALy) ......................................................................................... 71
8.9 Display Peak Reading (oPER > PEAk) ........................................................................................... 72
8.10 Standby Mode (oPER > Stby) ...................................................................................................... 72
8.11 Standby Mode (oPER > tARE) ...................................................................................................... 72
9. Specifications ...................................................................................................................................... 73
9.1 Inputs .......................................................................................................................................... 73
9.2 Control ........................................................................................................................................ 73
9.3 Outputs ....................................................................................................................................... 74
9.4 Communications (USB Standard, Optional Serial and Ethernet) ................................................ 74
9.5 Isolation....................................................................................................................................... 74
9.6 General ........................................................................................................................................ 75
10. Approvals Information ........................................................................................................................ 77
Figure 1 – CN8Pt, CN8DPt and CN8EPt Models: Back Panel Connections
(No Isolated Output Expansion Board Installed) ...................................................................... 10
Figure 2 – CN8Pt, CN8DPt and CN8EPt Models: Back Panel Connections
(With Isolated Output Expansion Board) ................................................................................... 10
Figure 3 – CN16Pt and CN32Pt Models: Back Panel Connections .............................................................. 11
Figure 4 – Main Power Connections ........................................................................................................... 11
Figure 5 – RTD Wiring Diagram ................................................................................................................. 13
Figure 6 – Process Current Wiring Hookup with Internal and External Excitation ............................... 13
Figure 7 – Process Voltage Wiring Hookup with optional Ratiometric Voltage connection. .............. 13
Figure 8 – PLATINUM Series Displays (CN8DPt and CN8EPt Shown) .......................................................... 16
Figure 9 – Circular Flow of Menus. ........................................................................................................... 17
Figure 10 – Alarm Range Option Diagram ................................................................................................ 50
Figure 11 – Alarm HI.HI parameter. ............................................................................................................ 51

Omega PLATINUM Series Specifications

General

Protection Class	IP20
Input Type	Thermocouple, RTD, Process
Output Type	Relay, SSR
Control Mode	ON/OFF, PID
Display Type	LED
Power Supply	100-240V AC, 24V DC
Communication	RS-485
Input Voltage	0 to 10 VDC
Output Voltage	0 to 10 VDC
Operating Temperature	0-50°C
Sampling Rate	100ms