Panasonic PT-RS30K

INF-38
SECTION 1 SERVICE INFORMATION
<RZ31K/RS30K>
Chapter 6 Maintenance — Light source/temperature/lter indicators
ENGLISH - 195
r When the Smoke Cut Filter (Model No.: ET-SFR330) is attached
Indicator status Status Solution
Lighting in red
f The lter is clogged.
f The runtime of the lter exceeds the
recommended time to replace the
lter.
f The temperature around or outside
the projector is abnormally high.
f Replace the Smoke Cut Filter in the following cases.
g The lter is dirty.
g The recommended time to replace the lter has been exceeded.
f Remove any objects if they are blocking the air intake/exhaust port.
f Do not use the projector at an altitude of 1 400 m (4 593') or higher above
sea level.
Blinking in red f [FILTER TYPE]
*1
is set to [NORMAL]. f Set [FILTER TYPE]
*1
to [SMOKE CUT].
*1 [FILTER TYPE] can be set in the [PROJECTOR SETUP] menu → [FILTER SETTING] → [FILTER TYPE].
Note
f If the lter indicator <FILTER> is still lit or blinking after taking the measures, ask your dealer for repair.
Chapter 6 Maintenance — Light source/temperature/lter indicators
194 - ENGLISH
Temperature indicator <TEMP>
Indicator status Status Solution
Lighting in red
f Warm-up status
f Wait ve minutes when the power is turned on while the temperature is low
(approximately 0 °C (32 °F)).
f Install the projector in a location with the operating environment temperature
between 0 °C (32 °F) and 50 °C (122 °F)
*1
.
f Internal temperature is high
(warning).
f Remove any objects if they are blocking the air intake/exhaust port.
f Install the projector in a location with the operating environment temperature
between 0 °C (32 °F) and 50 °C (122 °F)
*1
, and ambient humidity between
10 % and 80 % (no condensation).
f Perform maintenance
*2
or replace the lter if the lter indicator <FILTER>
lights up.
Blinking in red
(2 times)
f Internal temperature is high (standby
status).
Blinking in red
(3 times)
f The cooling fan has stopped.
f Turn the <MAIN POWER> switch to <OFF> .
*1 The operating environment temperature should be between 0 °C (32 °F) and 45 °C (113 °F) if the projector is used at an altitude between 1 400 m
(4 593') and 4 200 m (13 780') above sea level. However, when the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING
MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3], the operating environment temperature should be between 0 °C (32 °F) and 45 °C
(113 °F), and when the Smoke Cut Filter is used, it should be between 0 °C (32 °F) and 40 °C (104 °F), regardless of the altitude.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], the projector cannot be used at an altitude of 2 700 m (8 858') or higher above sea level. When the Smoke Cut Filter is used, the projector
cannot be used at an altitude of 1 400 m (4 593') or higher above sea level.
*2 Maintenance of the Smoke Cut Filter is not possible. Replace with new one.
Note
f If the temperature indicator <TEMP> is still lit or blinking after taking the measures, ask your dealer for repair.
Filter indicator <FILTER>
r When the air lter unit/Replacement Filter Unit (Model No.: ET‑EMF330) is attached
Indicator status Status Solution
Lighting in red
f The lter is clogged.
f The runtime of the lter exceeds the
recommended time to replace the
lter.
f The temperature around or outside
the projector is abnormally high.
f Perform maintenance or replacement of the lter in the following cases.
g The filter is dirty.
g The recommended time to replace the filter has been exceeded.
f Remove any objects if they are blocking the air intake/exhaust port.
f Do not use the projector at an altitude of 4 200 m (13 780')
*1
or higher
above sea level.
Blinking in red
f The air lter unit is not attached.
f The Long Life Filter Unit or Smoke
Cut Filter is not attached.
f Attach the air lter unit/Replacement Filter Unit.
*1 When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], the projector cannot be used at an altitude of 2 700 m (8 858') or higher above sea level.
r When the Long Life Filter Unit (Model No.: ET-EMFU330) is attached
Indicator status Status Solution
Lighting in red
f The lter is clogged.
f The runtime of the lter exceeds the
recommended time to replace the
lter.
*1
f The temperature around or outside
the projector is abnormally high.
f Perform maintenance or replacement of the lter in the following cases.
g The filter is dirty.
g The recommended time to replace the filter has been exceeded.
*1
f Remove any objects if they are blocking the air intake/exhaust port.
f Do not use the projector at an altitude of 4 200 m (13 780')
*2
or higher
above sea level.
Blinking in red f [FILTER TYPE]
*3
is set to [NORMAL]. f Set [FILTER TYPE]
*3
to [LONG LIFE].
*1 If the following two conditions are fullled, the recommended time to replace the lter is not set.
f The [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to anything other than [HIGH].
f The [PROJECTOR SETUP] menu → [FILTER SETTING] → [FILTER TYPE] is set to [LONG LIFE].
*2 When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], the projector cannot be used at an altitude of 2 700 m (8 858') or higher above sea level.
*3 [FILTER TYPE] can be set in the [PROJECTOR SETUP] menu → [FILTER SETTING] → [FILTER TYPE].