Panasonic WV-SP300 Series - Page 51

51
Fix shutter:Theselectedvaluewillbesetasthefixed
shutter speed.
  1/30fix,3/100fix,3/120fix,2/100fix,2/120fix,
1/100fix,1/120fix,1/250fix,1/500fix,1/1000fix,
1/2000fix,1/4000fix,1/10000fix
Default:Outdoorscene
Note:
 • Whenafastershutterspeedisselected,itispossi-
ble to capture a fast moving object with less blur.
 • Whenafastershutterspeedisselected,thesensi-
tivity will become lower. Smear also may appear
under bright light condition.
 • When"On"isselectedfor"Widedynamicrange
(WDR)",only"Outdoorscene","Indoorscene"
(60Hz) and "Indoor scene" (50Hz) are available.
[AGC]
Select a method of gain adjustment from the following.
On(High)/ On(Mid)/ On(Low): When the luminance of
the subject becomes darker, gain will be automati-
cally incremented and screen will become brighter.
"High", "Mid" and "Low" are indications of gain
level.
Off:Imageswillbecapturedwiththefixedgainlevel.
Default:On(High)
[Auto slow shutter]
The electronic sensitivity enhancement (sensitivity up)
can be carried out by adjusting the storage time of
MOS.
The following are available for the recording duration.
Off(1/30s),Max.2/30s,Max.4/30s,Max.6/30s,
Max.10/30s,Max.16/30s
Default:Off(1/30s)
Important:
 • When"On"isselectedfor"Autoslowshutter",
frame rate may become lower. Noise or white dots
(blemishes) may sometimes appear.
Note:
 • When"Max.16/30s"isselected,forexample,sensi-
tivitywillautomaticallybeincreaseduptox16.
 • When"On"isselectedfor"AGC",thissettingis
unavailable.
Important:
 • When"On"isselectedfor"Adaptiveblackstretch",
noise in the darker parts may be increased, and
parts around borders between the darker parts and
the brighter parts may become darker/brighter than
the other darker/brighter parts.
Note:
 • When"On"isselectedfor"Widedynamicrange
(WDR)", it is impossible to configure the "Adaptive
black stretch" setting.
[Back light compensation (BLC)]
Select"On"or"Off"todeterminewhetherornotto
activate the back light compensation (BLC) function.
When"On"isselectedfor"Widedynamicrange
(WDR)", this setting is unavailable.
The back light compensation function can compensate
back light by setting mask areas on brighter parts of
images brighter.
On: Mask areas will be set automatically.
Off: Mask areas will not be set automatically. It is nec-
essary to set them manually.
Default:Off
[Mask area]
When"Off"isselectedfor"Backlightcompensation
(BLC)", it is possible to compensate for backlight by
masking brighter areas.
Refer to page 49 for information on how to set the
mask area.
[Light control mode]
Select the light control mode from the following.
Outdoor scene: Depending on the brightness level
(illuminance), the iris will automatically be controlled
together with the shutter speed adjustment to con-
trol light. When shooting a bright subject such as
outdoor, etc., select this parameter. Be aware that
flicker may occur when a subject is under fluores-
cent lighting.
Indoor scene (50 Hz)
Indoor scene (60 Hz): The shutter speed will automati-
cally be adjusted to prevent flicker caused by fluo-
rescent light. Select 50 Hz or 60 Hz corresponding
to the location where the camera is in use.
ELC:
SP306
SP305
SP302
  Thisselectionissuitableforuseofalenswithfixed
iris or manual iris.