EasyManuals Logo

Polycom Vortex EF2211 User Manual

Polycom Vortex EF2211
123 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #22 background imageLoading...
Page #22 background image
This command sets or queries the status of the auto answer feature.
This command is a boolean command. See
Section 6.1 for more information on this type of command.
This command is saved to non-volatile memory only as part of a preset. The state of this command
will be restored after power-up only if a preset is saved and that preset is set to be the power-on
preset.
Example Description Status Message
S01AA1
Enable auto answer mode.
S01AA1
S01AA0
Disable auto answer mode.
S01AA0
S01AA2
Toggle auto answer mode.
S01AAx , where x is 0 or 1 depending on the current state of
auto answer mode.
S01AA?
Query auto answer mode.
S01AAx , where x is 0 or 1 depending on the current state of
auto answer mode.
8.2. ACKMOD -- Enable or Disable Acknowledgment Mode
This command controls whether or not status messages are sent. See Section 5 for more information
on status messages. This parameter is enabled by default, and it is rarely turned off by the host
controller.
This command is a boolean command. See Section 6.1 for more information on this type of command.
This command is saved to global non-volatile memory and is not part of a preset. Its value is saved
each time it is changed. It will retain its value after power-down. Since this command writes to non-
volatile memory, there will be a delay before an acknowledgment is returned.
Example Description Status Message
S01ACKMOD1
Enable acknowledgement mode.
S01ACKMOD1
S01ACKMOD0
Disable acknowledgement mode.
S01ACKMOD0
S01ACKMOD2
Toggle acknowledgement mode.
S01ACKMODx , where x is 0 or 1 depending on the
current state of acknowledgement mode.
S01ACKMOD?
Query acknowledgement mode.
S01ACKMODx , where x is 0 or 1 depending on the
current state of acknowledgement mode.
8.3. AEC -- Enable or Disable Acoustic Echo Cancellation
This command sets or queries the status of the Acoustic Echo Cancellation (AEC) algorithm on input
channel 1.
This command is a channel boolean command. See
Section 6.3 and Section 6.1 for more information
on this type of command.

Table of Contents

Other manuals for Polycom Vortex EF2211

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Polycom Vortex EF2211 and is the answer not in the manual?

Polycom Vortex EF2211 Specifications

Power IconPower
input voltage110-240 VAC
frequency47-63 Hz
power consumption25 W
phantom power24 V
Connectors IconConnectors
RS-232DB9F
EF Bus In/OutRJ45
Telephone Line/SetRJ11
Control/StatusDB25F
Audio3.5mm quick connect terminal blocks
Audio Specifications IconAudio Specifications
microphone input-30 dBu to +0 dBu
line inputs-20 dBu to +0 dBu
line outputs-20 dBu to +0 dBu
loudspeaker output10 W, 4-16 Ohms
input impedance10 k Ohms
output impedance50 Ohms
headroom20 dB
signal to noise ratio85 dB
frequency response20 Hz - 22 kHz
Echo and Noise Cancellation IconEcho and Noise Cancellation
total cancellation65 dB
convergence rate40 dB/second
noise cancellation0-15 dB
echo cancellation40 dB, total >65 dB
convergence30 dB/second
cancellation span32 ms
acoustic echo cancellation span270 ms
Operating Environment IconOperating Environment
operating temperature0 °C - 40 °C
status outputs5 V, 20 mA each
Weight and Dimensions IconWeight and Dimensions
width483 mm
length244 mm
height45 mm
weight1.8 kg
shipping weight2.5 kg

Related product manuals