Rohde & Schwarz FSW43 - Page 713

Remote Commands
R&S
®
FSW
713User Manual 1173.9411.02 ─ 19
11.5.3.7 Configuring MSR ACLR Measurements
If the "Multi-Standard Radio" standard is selected (see CALCulate<n>:MARKer<m>:
FUNCtion:POWer:PRESet on page 700), the channels for the ACLR measurement
are configured differently. (For more information see chapter 5.3.3.4, "Measurement on
Multi-Standard Radio (MSR) Signals", on page 145.)
In this case, use the following commands.
Useful commands for configuring MSR ACLR measurements described elsewhere:
● CALCulate<n>:MARKer<m>:FUNCtion:POWer:PRESet on page 700
● CALCulate<n>:MARKer<m>:FUNCtion:POWer:PRESet on page 700
● CALCulate<n>:MARKer<m>:FUNCtion:POWer:RESult:PHZ on page 721
● CALCulate<n>:MARKer<m>:FUNCtion:POWer:MODE on page 696
● CALCulate:LIMit:ACPower[:STATe] on page 711
● [SENSe:]POWer:ACHannel:REFerence:TXCHannel:AUTO on page 707
● [SENSe:]POWer:NCORrection on page 845
● [SENSe:]POWer:TRACe on page 699
● [SENSe:]POWer:ACHannel:MODE on page 722
● [SENSe:]POWer:ACHannel:PRESet on page 699
Remote commands exclusive to configuring MSR ACLR measurements
CALCulate:LIMit:ACPower:GAP<gap>:ABSolute...............................................................713
CALCulate:LIMit:ACPower:GAP<gap>:ABSolute:STATe....................................................714
CALCulate:LIMit:ACPower:GAP<gap>[:RELative]............................................................. 714
CALCulate:LIMit:ACPower:GAP<gap>[:RELative:]STATe.................................................. 715
CALCulate:LIMit:ACPower:GAP<gap>:RESult?................................................................ 715
[SENSe:]POWer:ACHannel:BANDwidth|BWIDth:GAP<gap>.............................................. 716
[SENSe:]POWer:ACHannel:FILTer:ALPHa:GAP<gap>...................................................... 716
[SENSe:]POWer:ACHannel:FILTer:ALPHa:SBLock<sb>:CHANnel<ch>.............................. 716
[SENSe:]POWer:ACHannel:FILTer:STATe:GAP<gap>...................................................... 716
[SENSe:]POWer:ACHannel:FILTer:STATe:SBLock<sb>:CHANnel<ch>.............................. 717
[SENSe:]POWer:ACHannel:SBCount...............................................................................717
[SENSe:]POWer:ACHannel:SBLock<sb>:BANDwidth|BWIDth[:CHANnel<ch>].....................717
[SENSe:]POWer:ACHannel:SBLock<sb>:CENTer[:CHANnel<ch>]..................................... 718
[SENSe:]POWer:ACHannel:SBLock<sb>:FREQuency:CENTer.......................................... 718
[SENSe:]POWer:ACHannel:SBLock<sb>:NAME[:CHANnel<ch>]?......................................718
[SENSe:]POWer:ACHannel:SBLock<sb>:RFBWidth..........................................................719
[SENSe:]POWer:ACHannel:SBLock<sb>:TECHnology[:CHANnel<ch>]...............................719
[SENSe:]POWer:ACHannel:SBLock<sb>:TXCHannel:COUNt............................................ 720
[SENSe:]POWer:ACHannel:SPACing:GAP<gap>..............................................................720
CALCulate:LIMit:ACPower:GAP<gap>:ABSolute <Limit>, <Reserved>
This command defines the absolute limit of the specified gap (CACLR) channel.
Configuring and Performing Measurements