Roland Groovebox MC-707

45
A drum track is a track that provides PCM synthesis and sample
playback functionality.
Simple Sound Editing
1.
In the home screen, use the cursor buttons to select the
drum track that you want to edit.
* If the sound source is Clip, select the clip that you want to edit.
2.
Hold down the [SHIFT] button and press the [SOUND]
button.
The KIT EDIT screen appears.
B
C
D
E
A
3.
Use the cursor buttons to select an icon.
4.
Use the [C1]–[C4] knobs to edit.
You can also select an icon and press the [ENTER] button to edit.
MEMO
Press the [FUNC] button to access the second page.
A PAD
You can use the [C1]–[C4] knobs to perform simple editing for the
selected pad.
Press the [ENTER] button to open the edit menu.
Parameter Value Explanation
LEVEL 0–127 Adjusts the volume.
COARSE -24–+24 Adjusts the pitch in semitone units.
RELEASE 0–1023
Species the time over which the sound
disappears after the key is released.
Larger values produce a longer decay, and
shorter values produce a crisper sound.
REVERB 0–127
Species the amount sent to TOTAL FX
REVERB.
FINE -50cen–+50cen Finely adjusts the pitch in one-cent units.
PAN L64–63R Species the pan of the sound.
ENV MODE NO-SUS, SUSTAIN
Species the behavior when a pad is
pressed.
NO-SUS: The volume immediately starts
decaying when you press the pad.
SUSTAIN: The volume starts decaying
when you release the pad.
DELAY 0–127
Species the amount sent to TOTAL FX
DELAY.
With a pad selected, press the [ENTER] button to access the pad
edit menu. Here you can exchange or edit sounds.
You can use the [C1]–[C4] knobs to perform simple editing of the
sound.
B COMP (DRUM+COMP track only)
If you select “COMP” and then press the [ENTER] button, the
compressor setting screen appears.
Six channels of compressors can be applied to one (and only one)
of the drum tracks.
When you create the track, specify whether it will have these
compressors.
If you use this track, the maximum number of Looper tracks is
reduced from six to four.
C SET
When you select “SET” and press the [ENTER] button, the setting
screen for the part parameters and drum kit appears.
You can use the [C1]–[C4] knobs to edit the reverb, delay, pan, and
level for the total eect.
Parameter Value Explanation
LEVEL
(MIX LEVEL)
0-127 Species the volume of the clip.
PAN L64–63R Species the pan of the sound.
>REVERB
(Reverb Send) 0–127
Species the amount sent to TOTAL FX
REVERB.
>DELAY
(Delay Send) 0–127
Species the amount sent to TOTAL FX
DELAY.
D MFX
Here you can edit the eect settings.
Parameter Value Explanation
SWITCH OFF, ON Turns the eect on/o.
TYPE
Refer to the MFX/
IFX parameters.
Switches the eect type.
Eect parameters
The parameters shown depend on the
selected eect type.
For details, refer to “Parameter List” (p. 61).
E NAME
Press the [ENTER] button to access the drum kit (KIT) name editing
screen.
Operating the Unit Explanation
Cursor [<] [>] buttons Selects the character to edit.
[C2] knob
Switches between uppercase, lowercase,
numerals, and symbols.
[C3] knob [C4] knob,
[VALUE] knob
Change the character.
Press the [C2] knob Inserts a space.
Press the [C3] knob Deletes a character.
Editing the DRUM Track