Roland Groovebox MC-707

83
Parameter List
Parameter Value Explanation
Density 0–127 Density of reverb
Diusion 0–127
Adjusts how reverb density increases over
time. (This eect is especially noticeable with
long reverb times.)
LF Damp Freq 50–4000 [Hz]
Frequency below which the low-frequency
portion of the reverb sound is cut.
LF Damp Gain -36–0 [dB] LF damp attenuation amount (0: no eect)
HF Damp Freq 4000–12500 [Hz]
Frequency above which the high-frequency
portion of the reverb sound is cut
HF Damp Gain -36–0 [dB] HF damp attenuation amount (0: no eect)
GS
Parameter Value Explanation
Character
ROOM1–3,
HALL1–2, PLATE,
DELAY, PAN-DELAY
Type of reverb
Pre-LPF 0–7
Amount of high-frequency attenuation for
the sound being input to the reverb
Time 0–127 Adjusts the decay length of the reverb sound.
Delay Feedback 0–127
Level at which the reverb sound is returned
to the input
SRV2000
Parameter Value Explanation
Selection
Selects the type of reverb oered by the Roland SRV-2000 digital
reverb.
Pre Delay
Room reverb.
Higher values increase the size of the room.
Time
Hall reverb.
Higher values increase the size of the concert
hall.
HF Damp
Plate reverb.
A more amboyant reverb sound than P-A.
Density Plate reverb.
Pre Delay 0–160
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time 1–990 [msec] Adjusts the decay length of the reverb sound.
HF Damp 0.05–1.00
Adjusts the high-frequency portion of the
reverb.
Density 0–9 Adjusts the density of the late reverberation.
Attack Gain 0–9 Adjusts the gain of the early reections.
Attack Time 0–9 Adjusts the time of the early reections.
ER Density 0–9 Adjusts the density of the early reections.
ER Level 0–99 Adjusts the volume of the early reections.
EQ Low Freq 0.04–1.00 [kHz] Frequency of the low range.
EQ Low Gain -24–+12 [dB] Gain of the low frequency range.
EQ Mid Freq 0.25–9.99 [kHz]
Adjusts the amount of mid-frequency boost/
cut.
EQ Mid Gain -24–+12 [dB]
Species the reference frequency of the mid-
frequency range.
EQ Mid Q 0.2–9.0
Species the width of the mid-frequency
range.
Set a higher value for Q to narrow the range
to be aected.
EQ Hi Freq 0.80–9.99 [kHz] Frequency of the high range.
EQ Hi Gain -24–+12 [dB] Gain of the high frequency range.
EQ Hi Q 0.2–9.0
Species the width of the high-frequency
range.
Set a higher value for Q to narrow the range
to be aected.
SRV2000
(NON-LINEAR)
Parameter Value Explanation
Pre Delay 0–160
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Reverb Time 1–990 [msec] Adjusts the decay length of the reverb sound.
Gate Time 10–450 [msec] Adjusts the decay length of the reverb sound.
HF Damp 0.05–1.00
Adjusts the high-frequency portion of the
reverb.
EQ Low Freq 0.04–1.00 [kHz] Frequency of the low range.
EQ Low Gain -24–+12 [dB] Gain of the low frequency range.
EQ Mid Freq 0.25–9.99 [kHz]
Adjusts the amount of mid-frequency boost/
cut.
EQ Mid Gain -24–+12 [dB]
Species the reference frequency of the mid-
frequency range.
EQ Mid Q 0.2–9.0
Species the width of the mid-frequency
range.
Set a higher value for Q to narrow the range
to be aected.
EQ Hi Freq 0.80–9.99 [kHz] Frequency of the high range.
EQ Hi Gain -24–+12 [dB] Gain of the high frequency range.
EQ Hi Q 0.2–9.0
Species the width of the high-frequency
range.
Set a higher value for Q to narrow the range
to be aected.
GM2 REVERB
Parameter Value Explanation
Character 0–5 Type of reverb
Time 0–127 Adjusts the decay length of the reverb sound.