Sanyo PLC-XU115 User Manual

63
Problem: –Solutions
No power –PlugthepowercordoftheprojectorintotheACoutlet.
  –SeeifthePOWERindicatorlightsred.
  –WaituntilthePOWERindicatorstopsblinkingtoturnontheprojector
again.TheprojectorcanbeturnedonafterthePOWERindicator
turnsred.Seepage22.
  –ChecktheWARNINGindicator.IftheWARNINGindicatorlightsred,
   projectorcannotbeturnedon.Seepage58.
  –Checktheprojectionlamp.Seepage61.
  –UnlocktheKeylockfunctionfortheprojector.Seepage54.
The initial display is not shown. –Makesure"Off"or"Countdownoff"arenotchosenatdisplay 
function.(seepage48)
The initial display is not same –Makesure"User"or"Off"arenotchosenatLogo(select)
as the default set. function.(seepage48)
Input signal switches automatically. –MakesureInputsearchfunctionisadjustedproperly.Seepage51.
(or does not switch automatically)
When the projector is on and you –ThatistheFilterwarningicon.Refertopage57.
press the input button, an icon
other than the Lamp mode icon
appears.
An icon other than Input mode or –ThatistheLampreplacementiconortheFilterwarningicon.See
Lamp mode icon appears. page56or57.
Image is out of focus. –Adjustfocusoftheprojector.Seepage26.
  –Provideproperdistancebetweentheprojectorandtheprojection
   screen.Seepage17.
  –Checktheprojectionlenstoseeifitneedscleaning.Seepage60.
  –Movingtheprojectorfromacooltowarmplacemayresultin 
   moisturecondensationontheprojectionlens.Insuchcases,leave
   theprojectoroffandwaituntilcondensationevaporates.
Image is Left/Right reversed. –ChecktheCeiling/Rearfunction.Seepage51.
Image is Top/Bottom reversed. –ChecktheTop/Bottomfunction.Seepage51.
Picture is not bright enough. –Checkifthe'Contrast"or"Brightness"areadjustedproperly.(see
   page37,44)
  –Checkif"Imagemode"isselectedproperly.(seepage36,43)
  –Checkthelampcontrolfunction.(seepage28)
  –ChecktheLAMPREPLACEindicator.Ifitlights,theendoflamplife
   isapproaching.Replacethelampwithanewonepromptly.(seepage
   61)
Appendix
Troubleshooting
Beforecallingyourdealerorservicecenterforassistance,checktheitemsbelowonceagain.
–Makesureyouhaveproperlyconnectedtheprojectortoperipheralequipmentasdescribedonpages19-21.
–MakesureallequipmentisconnectedtoACoutletandthepoweristurnedon.
–Whentheprojectordoesnotprojectanimagefromtheconnectedcomputer,restartthecomputer.
Downloaded From projector-manual.com Sanyo Manuals

Sanyo PLC-XU115 Specifications

General

Projection distance	0.93/11.47 m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	-40 - 40 °
I/O ports	SD Card Slot
Audio input	1
Aspect ratio	4:3
Special features	Soft Carry Bag
Networking features	Ethernet & Wireless
F-number (relative aperture)	1.7
Lamp type	NSH
Lamp power	275 W
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	3000 h
Dot clock scanning frequency	140 MHz
Analog signal format system	NTSC, PAL, SECAM
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power consumption (typical)	266 W

Weight and Dimensions

Package weight	3500 g