Sanyo PLC-XU115 User Manual

64
Appendix
No image –Checktheconnectionbetweenyourcomputerorvideoequipment
   andtheprojector.Seepages19-21.
  –Seeiftheinputsignaliscorrectlyoutputfromyourcomputer.Some
   laptopcomputersmayneedtochangethesettingformonitoroutput
  whenconnectingtoaprojector.Seeyourcomputer’sinstruction
   manualforthesetting.
  –Ittakesabout30secondstodisplayanimageafterturningonthe
   projector.Seepage22.
  –ChecktheInputsignal,colorsystem,videosystemorcomputer
systemmode.
  –MakesurethetemperatureisnotoutofthespecifiedOperating
   Temperature(41˚F–95˚F[5˚C–35˚C]).
  –When"NoShow"isoperating,theimagecannotbedisplayed.Press
   theNOSHOWbuttonoranyotherbuttonontheremotecontrol.
No sound –Checktheaudiocableconnectionfromaudioinputsource.
  –Adjusttheaudiosource.
  –PresstheVolume+button.Seepage27.
  –PresstheMutebutton.Seepage27.
 –WhentheAUDIOOUTisplugged-in,theprojector'sbuilt-inspeaker
   isnotavailable      
  –Istheimageprojected?Youwillhearthesoundonlywhentheimage
 isprojected.
The color is strange. –ChecktheInputsignal,colorsystem,videosystemorcomputer
   systemmode.      
  –Makesurethe"Blackboard"isnotselectedonImageselect 
   menu.(seepage36,43)
Some displays are not seen –ChecktheDisplayfunction.Seepage48.
during the operation.
Auto PC adjustment function –ChecktheInputsignal.AutoPCfunctioncannotworkwhen 
does not work.  480p,575p.720p,480i,575i,1035ior1080iisselectedorwhenthe
   digitalsignalisinputintoDVIterminal.(seePage34)
  –Theiconisnotavailableingrayoutwhenthedigitalsignalisinput.
The setting does not remain  –Makesureyouselected"Store"afteradjustingsetting.Somesettings
after turning off power.  cannotbestoredifnotregisteredwith"Store".(seepage45)
Power management does –Powermanagementfunctioncannotworkwhile"Freeze"or"No
work.  Show"functionisrunning.(seepage52)
Capture function does not work. –Checktheconnectionandtheinputsignaltoseeifthereissignal.
Auto setup does not work properly. –Makesure"Off"isnotselectedattheAutosetupfunction.(seepage
   47)
  –Makesure"On"isnotselectedattheCeilingfunction.(seepage51)
Auto keystone function does not  –MakesuretheAutokeystonefunctionisnotsetto"Manual".Press
work even when the projector is theAUTOSETUPbuttononthetopcontrol.(seepage26,47) 
tipped.
Downloaded From projector-manual.com Sanyo Manuals

Sanyo PLC-XU115 Specifications

General

Projection distance	0.93/11.47 m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	-40 - 40 °
I/O ports	SD Card Slot
Audio input	1
Aspect ratio	4:3
Special features	Soft Carry Bag
Networking features	Ethernet & Wireless
F-number (relative aperture)	1.7
Lamp type	NSH
Lamp power	275 W
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	3000 h
Dot clock scanning frequency	140 MHz
Analog signal format system	NTSC, PAL, SECAM
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power consumption (typical)	266 W

Weight and Dimensions

Package weight	3500 g