SECTION 2: INSTALLATION AND SETUP
Page 2-26 SATO HT200e
PROCESS ON THE SCREEN FOR TRANSFER OF TABLE DATA
6 + Power “ON”
[
←
][
→
]
[
←
][
→
]
[
←
][
→
]
Or:
Or:
Table data that are transferred from a host computer will be registered in a printer. The data registered in the
printer can be transferred to the host.
Note: When table data is transferred, on-line cable must be connected to the host before turning the power “ON”.
ＰＡＲＡＭＥＴＥＲ ＣＯＰＹ
1
ＰＲＩＮＴＥＲ ←→ ＣＡＲＤ
ＤＡＴＡ ＳＴＯＲＥ／ＲＣＡＬＬ
2
ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＰＲＥＳＥＴ ＳＴＲ／ＲＣＡＬＬ
3
ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＦＯＮＴ ＳＴＯＲＥ／ＲＣＡＬＬ
4
ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＴＡＢＬＥ ＳＴＲ／ＲＣＡＬＬ
5
ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＤＡＴＡ ＳＥＮＤ／ＲＥＣ
6
Ｈ Ｔ → Ｈ Ｏ Ｓ Ｔ ＨＯＳＴ→ＨＴ
ＨＴ→ＨＯＳＴ ＳＥＮＤ ＯＫ？
Ｙ ／Ｎ
ＨＯＳＴ→ＨＴ ＲＥＣ ＯＫ？
Ｙ ／Ｎ
ＳＥＮＤＩＮＧ
ＩＴＥＭ
:
０００１
ＲＥＣＥＩＶＩＮＧ
ＩＴＥＭ
:
０００１
Press [ENTR], so that it goes to the screen for the
selection of transferring print parameter.
Press [
←
], so that it returns to the process No. 1.
Press [
→
], so that it goes to the process No. 3.
Press [ENTR], so that it goes to the screen for the
selection of copying print parameter.
Press [
→
], so that it goes to the process No. 2.
Press [ENTR], so that it goes to the screen for the
selection of transfering preset.
Press [
←
], so that it returns to the process No. 2.
Press [
→
], so that it goes to the process No. 4.
Press [ENTR], so that it goes to the screen for the
selection of transfering font.
Press [
←
], so that it returns to the process No. 3.
Press [ENTR], so that it goes to the screen for the
selection of transfering table data.
Press [
←
], so that it returns to the process No. 4.
For the transfering direction, select [
←
] and [
→
],
and press [ENTR] to go to the screen for the
confirmation of receiving-and-sending.
Press [ENTR]:
“Y” is to start receiving and sending.
“N” is to return to the process No. 5.
When sending one item is complete, the number o
items will be added.
After sending, it returns to the process No. 5.
When receiving one item is complete, the number
items will be added.
After receiving, it returns to the process No. 5.
To Next Page
Loading...
