SECTION 2: INSTALLATION AND SETUP
SATO HT200e Page 2-27
PROCESS ON THE SCREEN FOR CURRENCY MARK SETTING
6 + Power “ON”
[
←
][
→
]
[
←
][
→
]
[
←
][
→
]
[
←
][
→
]
[
←
][
→
]
ＰＡＲＡＭＥＴＥＲ ＣＯＰＹ
1 ＰＲＩＮＴＥＲ ←→ ＣＡＲＤ
ＤＡＴＡ ＳＴＯＲＥ／ＲＣＡＬＬ
2 ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＰＲＥＳＥＴ ＳＴＲ／ＲＣＡＬＬ
3 ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＦＯＮＴ ＳＴＯＲＥ／ＲＣＡＬＬ
4 ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＴＡＢＬＥ ＳＴＲ／ＲＣＡＬＬ
5 ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＣＵＲＲＥＮＣＹ ＳＥＬＥＣＴ
6
ＣＵＲＲＥＮＣＹ ＳＥＬＥＣＴ
Ｄ Ｅ Ｆ Ａ Ｕ Ｌ Ｔ ＵＳＥＲ
ＣＵＲＲＥＮＣＹ ＣＲ １
ＨＯＬＬＡＮＤ ［ ｆ ]
Press [ENTR], so that it goes to the screen for the
selection of transferring print parameter.
Press [
←
], so that it returns to the process No. 1.
Press [
→
], so that it goes to the process No. 3.
Press [ENTR], so that it goes to the screen for the
selection of copying print parameter.
Press [
→
], so that it goes to the process No. 2.
Press [ENTR], so that it goes to the screen for the
selection of transfering preset.
Press [
←
], so that it returns to the process No. 2.
Press [
→
], so that it goes to the process No. 4.
Press [ENTR], so that it goes to the screen for the
selection of transfering font.
Press [
←
], so that it returns to the process No. 3.
Press [
→
], so that it goes to the process No. 5.
Press [ENTR], so that it goes to the screen for the
selection of table data.
Press [
←
], so that it returns to the process No.4.
Press [
→
], so that it goes to the process No. 6.
Press [ENTR], so that it goes to the screen for the
selection of currency mark.
Press [
←
], so that it returns to the process No. 5.
Select DEFAULT with [
←
] and [
→
] or choose USER,
and press [ENTR]: Where DEFAULT is selected,
Pound mark appears, from which it goes to the
screen for the card clear. While USER is selected, it
goes to the process No. 6.
Move with [
←
] and [
→
] to select currency mark, and
press [ENTR]. This permits to set the currency and
move to the screen for the card clear.
To Next Page
Loading...
