SATO HT200e - Page 98

SECTION 5 ： PRESET, TABLE DATA
Page 5-6 SATO HT200e
DELETION OF PRESET DATA
[RCL]
[
→ ]
[
→ ]
[
→ ]
[ENTR]
[ENTR]
[ENTR]
Note: Where asterisk mark or “*” can be seen in the upper right on the screen, entry by scanner can
be made
possible.
ＦＯＲＭＡＴ Ｎｏ
1［
・ ・］
ＨＴ２００ｅ
［ＰＲＥＳＥＴ］
2
Ｐ Ｒ Ｉ Ｎ Ｔ ＳＴＲ ＭＯＤＩＦＹ
ＤＥＬ ＤＵＭＰ ＭＡＳＴＥＲ
［ＰＲＥＳＥＴ］
3 ＰＲＩＮＴ
Ｓ Ｔ Ｒ ＭＯＤＩＦＹ
ＤＥＬ ＤＵＭＰ ＭＡＳＴＥＲ
［ＰＲＥＳＥＴ］
4 ＰＲＩＮＴ ＳＴＲ
Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
ＤＥＬ ＤＵＭＰ ＭＡＳＴＥＲ
［ＰＲＥＳＥＴ］
5 ＰＲＩＮＴ ＳＴＲ ＭＯＤＩＦＹ
Ｄ Ｅ Ｌ ＤＵＭＰ ＭＡＳＴＥＲ
ＰＲＥＳＥＴ ＮＯ ．ＩＮＰＵＴ＊
6
・ ・・・ ＜ＤＥＬＥＴＥ＞
ＰＲＥＳＥＴ ＤＥＬＥＴＥ ＯＫ
7 ・・－・・・・
Ｙ ／Ｎ
ＰＲＥＳＥＴ ＤＥＬＥＴＥＤ
8
The screen for the selection of preset printing will
be displayed: Press [
→ ], so that it goes to the
screen for the process No. 3.
Press [RCL], so that it goes from the modes of
the print to the preset.
The screen for the selection of preset deletion will
be displayed: Press [ENTR], so that it goes to the
entry of preset number.
The screen for the selection of preset storing will
be displayed: Press [
→ ], so that it goes to the
screen for the process No. 4.
The screen for the selection of preset modification
will be displayed: Press [
→ ], so that it goes to the
screen for the process No. 5.
The preset No. that is required to delete can be
entered: Press [ENTR], so that it appears the con-
firmation for deletion.
Use [
← ] and [ → ] to respond to the confirmation.
Press [ENTR], so that it deletes the preset data
specified.
When specified preset is deleted, it will display a
message for the end of deletion and returns to the
process No. 6.