Sharp AR-M550U - Adjust the Image Loss for Images Sent in Fax Mode; Adjust the Image Loss in Scanner Mode

AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 29
If an acceptable result is not obtained, do the following steps.
2) Repeat the process of changing the (TRAIL EDGE) adjustment
value and then pressing the Start key until attaining an acceptable
level.
Repeat the above adjustments until an acceptable result is obtained.
(Front/rear frame direction image loss adjustment)
1) Set the (FRONT/REAR) adjustment value to 20 by entering "20"
into the (FRONT/REAR) adjustment value field and then pressing
the P key.
Note that changing this adjustment value shifts the image position in
the front/rear frame direction.
1) Go through the modes specified in Simulation 50-27.
2) Using the numeric keypad, enter the number that corresponds to
the scanner mode adjustment item.
3) Press the Start key
4) Enter the adjustment value using the numeric keypad.
5) Press the Start key
(The adjustment value should be changed in steps of 1.0mm.)
Scanned images must be visually checked for image loss.
Note: Make adjustments in the same manner as in ADJ 8A and ADJ
8C.
1) Go through the modes specified in Simulation 50-27.
2) Enter the number that corresponds to the fax adjustment item
using the numeric keypad.
3) Press the Start key
4) Enter the adjustment value using the numeric keypad.
5) Press the Start key
(The adjustment value should be changed in steps of 1.0mm.)
Scanned images must be visually checked for image loss.
Note: Make adjustments in the same manner as in ADJ 8A and ADJ
8C.
ADJ 8D Adjust the image loss in scanner mode
Press [START] key. Press [CUSTOM SETTINGS] key.
Item Set range Default
FAX send
1 OC (LEAD_EDGE) OC lead edge 0 - 10
(Unit 1mm)
3
(3mm)
2 OC (FRONT/REAR) OC side
3 OC (TRAIL_EDGE) OC rear edge
4 SPF (LEAD_EDGE) SPF lead edge
5 SPF (FRONT/REAR) SPF side
6 SPF (TRAIL_EDGE) SPF rear edge
7 CIS (LEAD_EDGE) CIS lead edge
8 CIS (FRONT/REAR) CIS side
9 CIS (TRAIL_EDGE) CIS rear edge
Scanner mode
10 OC (LEAD_EDGE) OC lead edge 0 - 10
(Unit 1mm)
0
(0mm)
11 OC (FRONT/REAR) OC side
12 OC (TRAIL_EDGE) OC rear edge
13 SPF (LEAD_EDGE) SPF lead edge
14 SPF (FRONT/REAR) SPF side
15 SPF (TRAIL_EDGE) SPF rear edge
16 CIS (LEAD_EDGE) CIS lead edge
17 CIS (FRONT/REAR) CIS side
18 CIS (TRAIL_EDGE) CIS rear edge
1
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND
PRESS START.
[FAX]
1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR) 0 3.OC(TRAIL_EDGE) 0
4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR) 0 6.SPF(TRAIL_EDGE) 0
7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR) 0 9.CIS(TRAIL_EDGE) 0
[SCN]
10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR) 0 12.OC(TRAIL_EDGE) 0
13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR) 0 15.SPF(TRAIL_EDGE) 0
16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR) 0 18.CIS(TRAIL_EDGE) 0
0
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND
PRESS START.
1.OC(LEAD_EDGE)
ADJ 8E Adjust the image loss for images sent in
fax mode
Press [START] key. Press [CUSTOM SETTINGS] key.
Item Set range Default
FAX send
1 OC (LEAD_EDGE) OC lead edge 0 - 10
(Unit 1mm)
3
(3mm)
2 OC (FRONT/REAR) OC side
3 OC (TRAIL_EDGE) OC rear edge
4 SPF (LEAD_EDGE) SPF lead edge
5 SPF (FRONT/REAR) SPF side
6 SPF (TRAIL_EDGE) SPF rear edge
7 CIS (LEAD_EDGE) CIS lead edge
8 CIS (FRONT/REAR) CIS side
9 CIS (TRAIL_EDGE) CIS rear edge
Scanner mode
10 OC (LEAD_EDGE) OC lead edge 0 - 10
(Unit 1mm)
0
(0mm)
11 OC (FRONT/REAR) OC side
12 OC (TRAIL_EDGE) OC rear edge
13 SPF (LEAD_EDGE) SPF lead edge
14 SPF (FRONT/REAR) SPF side
15 SPF (TRAIL_EDGE) SPF rear edge
16 CIS (LEAD_EDGE) CIS lead edge
17 CIS (FRONT/REAR) CIS side
18 CIS (TRAIL_EDGE) CIS rear edge
1
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND
PRESS START.
[FAX]
1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR) 0 3.OC(TRAIL_EDGE) 0
4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR) 0 6.SPF(TRAIL_EDGE) 0
7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR) 0 9.CIS(TRAIL_EDGE) 0
[SCN]
10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR) 0 12.OC(TRAIL_EDGE) 0
13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR) 0 15.SPF(TRAIL_EDGE) 0
16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR) 0 18.CIS(TRAIL_EDGE) 0
0
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND
PRESS START.
1.OC(LEAD_EDGE)