Sharp AR-M550U - Adjust the Copied Image Gamma in Copy Mode

: Feb. 9 2004
1
AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 32
(SIM 46-10) (Text/photo mode)
(SIM 46-11) (Photo mode)
3) Using the numeric keypad, select the number that corresponds to
the copy density adjustment level. (Choose from numbers 3 to 11.)
4) Press the Start key
5) Press the Start key (A copy is created.)
If the copied image density is not at an acceptable level, do the fol-
lowing steps.
6) Adjust the copy density by entering an appropriate value through
the numeric keypad.
A larger value provides higher density.
7) Press the P or Start key.
This applies the adjustment value.
Pressing the Start key starts copy operation as well as applying the
adjustment value.
8) Check the copied image density.
Repeat steps 5 to 9 until an acceptable copied image density is
obtained.
1) Set the original on the original table.
2) Go through the modes specified in Simulation 46-18.
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection
1 COPY START Copy START (Default)
2 EXP LEVEL Exposure level selection
3 1.0 Exposure level 1.0 0 - 99 50
4 1.5 Exposure level 1.5
5 2.0 Exposure level 2.0
6 2.5 Exposure level 2.5
7 3.0 Exposure level 3.0
8 3.5 Exposure level 3.5
9 4.0 Exposure level 4.0
10 4.5 Exposure level 4.5
11 5.0 Exposure level 5.0
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection
1 COPY START Copy START (Default)
2 EXP LEVEL Exposure level selection
3 1.0 Exposure level 1.0 0 - 99 50
4 1.5 Exposure level 1.5
5 2.0 Exposure level 2.0
6 2.5 Exposure level 2.5
7 3.0 Exposure level 3.0
8 3.5 Exposure level 3.5
9 4.0 Exposure level 4.0
10 4.5 Exposure level 4.5
11 5.0 Exposure level 5.0
ADJ 9E Adjust the copied image gamma in copy
mode
Select 2, and
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level selection
3 OC_AE AE mode (OC) 0 - 127 64
4 OC_CHARA Text mode (OC)
5 OC_MIX Text/Photo mode (OC)
6 OC_PHOTO Photo mode (OC)
7 SPF_AE AE mode (SPF)
8 SPF_CHARA Text mode (SPF)
9 SPF_MIX Text/Photo mode (SPF)
10 SPF_PHOTO Photo mode (SPF)
11 CIS_AE AE mode (CIS)
12 CIS_CHARA Text mode (CIS)
13 CIS_MIX Text/Photo mode (CIS)
14 CIS_PHOTO Photo mode (CIS)
64
1
SIMULATION 46-18
GAMMA SETUP(COPIER). SELECT 1-14, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1
3.OC_AE 64 4.OC_CHARA 5.OC_MIX 64
6.OC_PHOTO 64 7.SPF_AE 64 8.SPF_CHARA 64
9.SPF_MIX 64 10.SPF_PHOTO 64 11.CIS_AE 64
12.CIS_CHARA 64 13.CIS_MIX 64 14.CIS_PHOTO 64
SIMULATION 46-18
GAMMA SETUP. INPUT VALUE 0-127, AND PRESS START.
3.OC_AE
SIMULATION 46-18
GAMMA SETUP. NOW PRINTING.
SIMULATION 46-18
GAMMA SETUP. SELECT 1-6, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
Select other than 0 - 2,
and press [START] key.
Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
Select 1,
and press
[START] key.
Select 0, and press [START] key.
1
SIMULATION 46-18
EXP.LEVEL SETUP FAX(SUPER FINE). SELECT 3-14, AND PRESS
START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0 5.2.0
6.3.0 7.4.0 8.5.0
9.AUTO(H) 10.1.0(H) 11.2.0(H)
12.3.0(H) 13.4.0(H) 14.5.0(H)