: Feb. 9 2004
1
AR-M550/M620/M700 OTHER 12 - 5
(10)Reset and set for suplly counters
B. Location and display of each counter data
Work item Test Command Reset item Included Test Command
Setting the toner concentration control level
Sim25-2
Developer counter Sim24-5
DV unit running time counter (sec) Sim24-11
Reset the OPC drum counter Sim24-7 OPC drum counter —
Reset the Developer counter Sim24-5 Developer counter —
Reset the OPC drum running time counter (sec) Sim24-11 OPC drum running time counter (sec) —
Reset the DV running time counter (sec) Sim24-11 DV running time counter (sec) —
Simulation
Code
Operation content
Data
size
Data location
Conforming count mode
(SIM 26-5)
Count-up condition
Main Sub
MFP
control
PWB
FAX
Scanner
control
PWB
PCU
PWB
TOTAL
Mainte-
nance
DV
22 01 Each counter display (Total/ Mainte-
nance/ Developer/ SPF/ Staple/ Tray)
1: Total counter ●■
2: Drum cartridge counter ● ■
3: Toner cartridge counter ●■
4: Deve cartridge counter ●■
5: Maintenance counter ●■
6: Total output page number counter ●■
7: Copy counter ●■
8: Printer counter ●■
9: FAX output counter ●■
10: I-FAX output counter ●■
11: Document filing output counter ●■
12: Right side output counter ●■ Count is made when the main unit paper exit is started. (When POP2
is ON)
13: Other print counter ●■Refer to the “Count Specifications.”
02 Jam/ Trouble counter display
1: Paper jam ● ———Count is made when an event occurs. (A jam by closing the door dur-
ing paper transport is not counted.)
2: SPF jam ● ———Count is made when an event occurs. (A jam by closing the door dur-
ing paper transport is not counted.)
3: Trouble ● ———Count is made when an event occurs. (Follows the trouble count
method of SIM 26-35.)
08 Document, staple counter display
1: SPF document feed page number ● ———One count is made every time when SPF document is paper feed.
2: Scan number ● ———One count is made every time when scan is completed.
3: Staple number ● ———One count for every stapling (Stapling at two positions is counted as
2.)
4: Punch number ● ———One count for every punching
5: SPF finish stamp number ● ———One count when stamp is started.
6: Saddle staple number ● One count for every saddle stapling
7: Inserter number ● One count for every paper pick-up
09 Paper feed counter display
1: Paper feed tray 1 (Tandem Left) ● ———One count for every paper pick-up
2: Paper feed tray 2 (Tandem Right) ● ———One count for every paper pick-up
3: Paper feed tray 3 ● ———One count for every paper pick-up
4: Paper feed tray 4 ● ———One count for every paper pick-up
5: MFT (Manual paper feed tray) ● ———One count for every paper pick-up
6: ADU ● ———One count for every paper transport start from ADU.
7: LCC ● One count for every paper pick-up
11 FAX send/receive counter display
1: FAX send (Send counter) 32bit ● ———Accumulated page number of send
• Except for the serial transmit operation, one reservation is counted
as one communication.
• For the serial transmit operation, count is made for each communi-
cation individually.
• Recall is not included.
• Saved in the FAX-SRAM.
2: FAX receive (Receive counter) 32bit ● ———Accumulated number
• Count is made regardless of normal or abnormal completion.
• Saved in the 32bit counter and the FAX-SRAM.
3: FAX output (FAX print counter) 32bit ●■The accumulated page number of FAX receive print
Count by size and count in recovery are the same as the copier spec-
ifications.
• Counted by the print system.
Refer to the “Count Specifications.”
4: FAX send images (Send page
number)
32bit ● ———Accumulated page number of send
• In the serial transmit operation, each communication is counted as
one individually.
• Saved in the 32bit counter and the FAX-SRAM.
5: Send time (Send time) 48bit ● ———hhhhhhhh:mm:ss
Saved in the FAX-SRAM.
6: Receive time (Receive time) 48bit ● ———hhhhhhhh:mm:ss
Saved in the FAX-SRAM.
1
To Next Page
Loading...
