Siemens S7-1200 - Page 1009

Index
S7-1200 Programmable controller
System Manual, 03/2014, A5E02486680-AG
1009
CEIL (generate next higher integer from floating-
point number), 250
Chars_TO_Strg (convert array of CHAR to
character string), 302
clock, 287
columns and headers, 42, 746
common parameters, 548
compare values, 226
CONCAT (combine character strings), 307
CONTINUE (SCL), 273
CONV (convert value), 245
COS (form cosine value), 236
CTD (count down), 220
CTRL_HSC (control high-speed counter), 409
CTRL_PWM (pulse width modulation), 364
CTU (count up), 220
CTUD (count up and down), 220
DataLogClose (close data log), 389
DataLogCreate (create data log), 382
DataLogNewFile (data log in new file), 390
DataLogOpen (open data log), 385
DataLogWite (write data log), 387
date, 283
DEC (decrement), 232
DECO (decode), 276
DELETE (delete characters in a character
string), 310
DETACH (detach an OB from an interrupt
event), 331
DeviceStates (read module status of an I/O
system), 347
DIS_AIRT (disable execution of higher priority
interrupts and asynchronous error events), 344
DIV (divide), 230
DPNRM_DG (read diagnostic data from a DP
slave), 328
DPRD_DAT (read consistent data of a DP standard
slave), 326
DPWR_DAT (write consistent data of a DP standard
slave), 326
drag and drop, 38
drag and drop between editors, 43
EN_AIRT (enable execution of higher priority
interrupts and asynchronous error events)), 344
ENCO (encode), 276
ENDIS_PW (enable disable passwords), 259
EXIT (SCL), 273
EXP (form exponential value), 236
expandable instructions, 42
EXPT (exponentiate), 236
F_TRIG (set tag on negative signal edge), 210
favorites, 38
FieldRead (read field), 240
FieldWrite (write field), 240
FILL_BLK (fill block), 242
FIND (find characters in a character string), 313
FLOOR (generate next lower integer from floating-
point number), 250
FOR (SCL), 270
force, 801
force operation, 802
FRAC (return fraction), 236
GET (read data from a remote CPU), 587
GET_DIAG (read diagnostic information), 358
GET_ERROR (get error locally), 263
GET_ERROR_ID (get error ID locally), 265
GOTO (SCL), 274
HSC (high-speed counter), 411
HTA (convert hexadecimal number to ASCII
string), 304
IF-THEN (SCL), 268
IN_Range (value within range), 227
INC (increment), 232
INSERT (insert characters in a character
string), 311
inserting, 38
INV (create ones complement), 276
JMP (jump if RLO = 1), 254
JMP_LIST (define jump list), 255
JMPN (jump if RLO = 0), 254
Label (jump label), 254
LED (read LED status), 346
LEFT (read the left characters of a character
string), 308
LEN (determine the length of a character
string), 307
LIMIT (set limit value), 235
LN (form natural logarithm), 236
LOG2GEO (Determine the slot from the hardware
identifier), 404
MAX (get maximum), 234
MAX_LEN (maximum length of a character
string), 306
MB_CLIENT (communicate via PROFINET as
Modbus TCP client), 730
MB_COMM_LOAD (configure port on the PtP
module for Modbus RTU), 747
MB_MASTER (communicate via the PtP port as
Modbus master), 749
MB_SERVER (communicate via PROFINET as
Modbus TCP server), 736
MB_SLAVE (communicate via the PtP port as
Modbus slave), 755