01.99 1 NC/Drive Machine Data
1.5 General bits
5021
1)
Neutral pos.
of outputs f.
mode gr. 6
Neutral pos.
of outputs f.
mode gr. 5
Neutral pos.
of outputs f.
mode gr. 4
Neutral pos.
of outputs f.
mode gr. 3
Neutral pos.
of outputs f.
mode gr. 2
Neutral pos.
of outputs f.
mode gr. 1
5022
1)
NC-Ready
signal delay by
1 Ipo cycle
with PLC
failure or 5 V
undervoltage
(from SW 6.3)
Consid. SW
limit switch
Emergency
retract. (from
SW 6)
5 V under-
voltage
(from
SW 6.3)
Retract when
PLC failure
(from
SW 6.3)
Extended
stopping
Stopping
also on
Emerg. OFF
5024
Autom. bl. end
value synchr.
G105/G119
Abort
on
contour vio-
lation CRC
5025
Reload
workpiece at
POWER ON
(SW2+)
Endlessly
turning
rotary axis
"Alarm" axis
not in C axis
mode (from
SW 5)
Travel thru
transform.
centre
2)
Extended
threading
package
Axis-specific
G function to
PLC 1)
5026
2nd MCS
mirroring Z
3)
2nd MCS
mirroring Y
3)
2nd MCS
mirroring X
3)
5027
3rd MCS
mirroring Z
3)
3rd MCS
mirroring Y
3)
3rd MCS
mirroring X
3)
5028
4th MCS
mirroring Z
3)
4th MCS
mirroring Y
3)
4th MCS
mirroring X
3)
5029
Dynamic SW
limit switch
Following
axes
3)
5030
from
SW 6.3
CSB input 7
signal from
UPS: power
failure
CSB input 6
signal from
UPS: power
failure
CSB input 5
signal from
UPS: power
failure
CSB input 4
signal from
UPS: power
failure
CSB input 3
signal from
UPS: power
failure
CSB input 2
signal from
UPS: power
failure
CSB input 1
signal from
UPS: power
failure
CSB input 0
signal from
UPS: power
failure
5038
Declaration
of PLC (up
to SW 3)
5039
Display PLC
config. (up
to SW 3)
5040
5041
5042
5043
5044
5051
Cycle
setting data
5052
F62 pro-
gramming
(from SW 6.3)
Progr. predec.
with G171/172
(from SW 5)
Cylinder
interpol. with
4 axes (SW 6)
No automat.
gen. of
G68
2)
5053
Display of
axes for all
mode groups
(from SW 6)
Channel-spec.
axis a. spindle
display
2)
5060
5061
5062
5063
5064
5065
5066
5067
5068
5069
7 6 5 4 3 2 1 0
Bit No.
MD No.
5th real axis (1st transformation block)
4th real axis (1st transformation block)
3rd real axis (1st transformation block)
2nd real axis (1st transformation block)
1st real axis (1st transformation block)
3rd fictitious axis (1st transformation block)
G function for transformation selection (1st transformation block)
Channel number of the transformation (1st transformation block)
1st fictitious axis (1st transformation block)
2nd fictitious axis (1st transformation block)
Bits for menu selection
1)
Bits for menu selection
1)
Bits for menu selection
1)
Bits for menu selection
1)
Bits for menu selection
1)
1) SW 4 and higher
2) SW 5 and higher
3) SW 6 and higher
© Siemens AG 1992 All Rights Reserved 6FC5197- AA60
1–19
SINUMERIK 840C (IA)
To Next Page
Loading...
Need help?
General
