Strong SRT 7015 User Manual

21
These must have selected before in the Satellite List.
The procedure is the same as for Single Satellite Search, except for the Satellites mentioned in the top line. All
those will be scanned one after the other.
7.1.5 Transponder Edit Options
Scanning by transponder (Manual Scan)
Select TP List in the Installation menu.
The transponder list is shown for the in the top line selected satellite.
Search Use the pq buttons to highlight the transponder you want to scan and press
OK or BLUE for Search. A window with scanning settings will be displayed.
After conguring the settings press OK to start the scanning of the highlighted
transponder. When the scan process has been completed, all new found channels
will be added to the end of the channel list.
Options are:
FTA Only: Press tu to select No to search for (scrambled and free) channels or {Yes to search
for Free to Air channels only.
NOTE: Scrambled channels can not be watched with this receiver.
Scan Channel: Press tu to select TV+Radio, TV Channel or Radio
Network Search Use tu to select Yes or No. Some providers use more than one transponder to
transmit their Pay-TV programmes. Select Yes and one of those transponders and
it will nd the corresponding transponders as well. Note: This is only applicable for
scrambled channels, which can not be seen with this receiver.
7.1.5.1 Transponder List
Transponder Edit options
While in the TP list menu, you can use the coloured buttons to make changes.
The options below are now available.
Edit: Press RED to edit the highlighted transponder. In the pop-up banner, change the
transponder´s parameters by using the pq tu and numeric buttons. Conrm
changes with OK or cancel with .
Add: Press to add a new transponder. In the pop-up banner, enter the transponder´s
parameters by using the pq tu and the numeric buttons. Conrm the settings
with OK or cancel with . An existing TP cannot be stored again under the same
satellite. A pop-up message will inform you if the transponder already exists in the
list.
Delete transponder: Press YELLOW to delete the highlighted transponder. Select Yes and press OK to
conrm or  to cancel.
7.1.5.2 Satellite Edit options
While in the Satellite List menu.
Edit: Press RED to edit the focused satellite.
Edit the Satellite name and/or position. Use the numeric buttons to enter characters.
Conrm with YELLOW.
Add: Press GREEN to add a new satellite.
Use the numeric buttons to enter characters for a new Satellite's name and position.
Conrm with YELLOW.
Delete: To Delete a Satellite, select the Satellite from the list and press BLUE. Conrm the
popup pop-up screen.
To Delete a Satellite, select the Satellite from the list and press BLUE. Conrm the popup pop-up screen.

Strong SRT 7015 Specifications

General

Flash memory	4 MB
Internal memory	64 MB
Signal source	Satellite
Supported video modes	480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Digital signal format system	DVB-S, DVB-S2
Personal Video Recorder (PVR) included	-
AC input voltage	100 – 240 V
AC input frequency	50/60 Hz
Power consumption (typical)	- W
Storage temperature (T-T)	-10 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
AC adapter included	Yes
Ethernet LAN	No
Tuner type	Digital
Demodulation	8PSK, QPSK
Product color	Black
Audio decoders	Dolby Digital, Dolby Digital Plus
Frequency range	950 - 2150 MHz
Number of tuners	- tuner(s)
Channels quantity	2000 channels
Audio output channels	2.0 channels
Digital Satellite Equipment Control (DiSEqC)	1.2, 1.3
Composite video out	1
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Audio formats supported	AC3
Video formats supported	H.264, MPEG2, MPEG4

Weight and Dimensions

Depth	41 mm
Width	171 mm
Height	104 mm
Weight	260 g