What to do if Sumitomo Cables and connectors splicer does not power up?
If your Sumitomo Cables and connectors splicer isn't powering up, check the following: * Make sure the battery pack is correctly installed in the module bay. * Verify the power plug is properly connected and seated, ensuring the power cord is connected to the AC adapter. * Ensure the battery is fully charged.
Why is my Sumitomo Cables and connectors fiber breaking?
Fiber breaking during splicing can occur for several reasons. It could be due to a weak arc power level, in which case you should re-do an arc test. Another cause might be dirty V-grooves or bare fiber pads; ensure these are thoroughly cleaned. Also, check the condition of your jacket remover/fiber cleaver, as deterioration can cause issues. Clean the jacket remover/fiber cleaver completely.
Why is Sumitomo Cables and connectors splicer running slow?
If your Sumitomo Cables and connectors splicer is running slow, it might be due to frequent screen switching. Try turning the splicer off and then on again to resolve this issue.
General| Fiber Alignment | Core Alignment |
|---|---|
| Typical Splice Loss (SM) | 0.02dB |
| Typical Splice Loss (MM) | 0.01dB |
| Typical Splice Loss (DS) | 0.04dB |
| Typical Splice Loss (NZDS) | 0.04dB |
| Return Loss | ≥60dB |
| Electrode Life | 3000 splices |
| Automatic Heating Start | Yes |
| Operating Condition - Altitude | 0 to 5000m |
| Category | Fusion Splicer |
| Model | T-400S |
| Applicable Fibers | SM, MM, DS, NZDS |
| Splicing Time | 9 seconds |
| Applicable Fiber Protection Sleeve | 40 mm, 60 mm |
| Data Output | USB |
| Power Supply | AC adapter, Battery |
| Operating Condition - Temperature | -10 to 50°C |
| Operating Condition - Humidity | 0 to 95% (non-condensing) |
| Storage Condition - Humidity | 0 to 95% (non-condensing) |
| Storage Condition - Battery Temperature | -20°C to 30°C (long term) |
| Manufacturer | Sumitomo |
| Type | Fusion splicer |
| Fiber Type | SM, MM, DS, NZDS |
| Core Diameter | 125µm |
| Cladding Diameter | 125 µm |
| Operating Temperature | -10°C to 50°C |
| Storage Condition - Temperature | -20°C to 60°C |
| Storage Temperature | -20°C to 60°C |
Explains product/manual symbols for warnings and cautions to prevent accidents and damage.
Safety guidelines for setting up, using, transporting, and handling the splicer and its parts.
Provides a general introduction to the T-400S Fusion Splicer and its capabilities.
Specifies compatible optical fiber types and specifications for the T-400S.
Highlights the key features and functionalities of the T-400S, such as Auto start and ECO Mode.
Lists required equipment and summarizes the splicing and protection steps.
Details AC/Battery operation, charging, and precautions.
Guides through stripping, cleaving, inserting fibers, arc testing, and splicing.
Guides on applying splice protection and evaluating splice quality.
Instructions for cleaning various components like V-grooves, LEDs, and pads.
Explains when and how to replace electrodes to maintain splicing performance.
Details how to pack and store the T-400S and accessories safely.
Guides on selecting and setting up splice/heater programs.
Guides on changing operation and function settings.
Details splice, heater, operation, and function settings in administrator mode.
Details steps to log in and access Administrator menu.
Guides on changing passcode and setting up startup passwords.
Explains how to lock/unlock programs and settings.
Addresses issues like arc problems, no power, and slow operation.
Lists common error messages and their countermeasures.
Explains warranty, exceptions, and service procedures.
Lists technical specs like fiber compatibility, performance, functions, and conditions.
To Next Page
