TAJIMA TEHX-C - M.shaft Inching after Ath; Auto Jump [MM]; Jump Convert

CHAPTER 8 PARAMETER SETTING
82
6. M.Shaft Inching after ATH
7. Auto Jump [mm]
8. Jump Convert
9. ------
10. ------
It makes the machine perform inching the number
of set times at machine start after thread trimming.
Yes
Yes
No
No
0
4
No
3
(2 ~ 9)
1. Auto Color Change (AC)
( No, Yes, )
2. Auto Start (AS)
( No, Yes, )
3. A.S. in the Same Color
( No, Yes, )
4. A. S. after Auto Data Set
( No, Yes, )
5. Main Shaft Inching
( 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
6. M.Shaft Inching after ATH
( 2, 3, 4, 5, 6, 7, 8, 9, )
7. Auto Jump [mm]
( No, 4.0 ~ 9.9, )
8. Jump Convert
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
------
------
4
(GC02)
When a stitch length is longer than the auto jump
length being set, it will make the stitch perform
auto jump.
“No” does not make auto jump.
Yes
Yes
No
No
0
4
No
3
(No/ 4.0~9.9)
1. Auto Color Change (AC)
( No, Yes, )
2. Auto Start (AS)
( No, Yes, )
3. A.S. in the Same Color
( No, Yes, )
4. A. S. after Auto Data Set
( No, Yes, )
5. Main Shaft Inching
( 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
6. M.Shaft Inching after ATH
( 2, 3, 4, 5, 6, 7, 8, 9, )
7. Auto Jump [mm]
( No, 4.0 ~ 9.9, )
8. Jump Convert
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
------
------
No
When jump codes continue the number of set
times and more consecutively, it converts the con-
secutive jump codes to frame stepping.
Frame stepping moves the frame with the
main shaft kept stopping.
“No” does not make jump conversion.
It is not possible to convert automatic jump.
Yes
Yes
No
No
0
4
No
3
(No/ 1~9)
1. Auto Color Change (AC)
( No, Yes, )
2. Auto Start (AS)
( No, Yes, )
3. A.S. in the Same Color
( No, Yes, )
4. A. S. after Auto Data Set
( No, Yes, )
5. Main Shaft Inching
( 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
6. M.Shaft Inching after ATH
( 2, 3, 4, 5, 6, 7, 8, 9, )
7. Auto Jump [mm]
( No, 4.0 ~ 9.9, )
8. Jump Convert
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
------
------
3
It is not applied.
Yes
Yes
No
No
0
4
No
3
1. Auto Color Change (AC)
( No, Yes, )
2. Auto Start (AS)
( No, Yes, )
3. A.S. in the Same Color
( No, Yes, )
4. A. S. after Auto Data Set
( No, Yes, )
5. Main Shaft Inching
( 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
6. M.Shaft Inching after ATH
( 2, 3, 4, 5, 6, 7, 8, 9, )
7. Auto Jump [mm]
( No, 4.0 ~ 9.9, )
8. Jump Convert
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
------
------
It is not applied.
Yes
Yes
No
No
0
4
No
3
1. Auto Color Change (AC)
( No, Yes, )
2. Auto Start (AS)
( No, Yes, )
3. A.S. in the Same Color
( No, Yes, )
4. A. S. after Auto Data Set
( No, Yes, )
5. Main Shaft Inching
( 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
6. M.Shaft Inching after ATH
( 2, 3, 4, 5, 6, 7, 8, 9, )
7. Auto Jump [mm]
( No, 4.0 ~ 9.9, )
8. Jump Convert
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
------
------