CHAPTER 8 PARAMETER SETTING
85
21. Select Under T. Trimming [mm]
22. Return Stitches (ATH)
23. Tie Stitches
24. Tie/Return Stitch Length [mm]
25. Preset Halt (Stitch)
(GC02)
It is not available at present.
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
22. Return Stitches (ATH)
( -, 1, 2, )
23. Tie Stitches
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
25. Preset Halt (Stitch)
( 0 ~999999 st., )
26. Preset Halt (Data)
( 0 ~99999 cm, )
27. Preset Halt (Design)
( 0 ~999 Designs, )
28. Preset Halt (Lubrication)
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
30. Language
( English, Japnese, Other, )
0
It makes the machine perform return stitching
when the machine starts to sew after thread trim-
ming.
“-” makes no return stitching.
(-, 1, 2)
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
22. Return Stitches (ATH)
( -, 1, 2, )
23. Tie Stitches
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
25. Preset Halt (Stitch)
( 0 ~999999 st., )
26. Preset Halt (Data)
( 0 ~99999 cm, )
27. Preset Halt (Design)
( 0 ~999 Designs, )
28. Preset Halt (Lubrication)
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
30. Language
( English, Japnese, Other, )
-
It makes the machine perform tie stitching before
thread trimming.
Yes To perform tie stitching
No Not to perform tie stitching
(Yes/No)
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
22. Return Stitches (ATH)
( -, 1, 2, )
23. Tie Stitches
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
25. Preset Halt (Stitch)
( 0 ~999999 st., )
26. Preset Halt (Data)
( 0 ~99999 cm, )
27. Preset Halt (Design)
( 0 ~999 Designs, )
28. Preset Halt (Lubrication)
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
30. Language
( English, Japnese, Other, )
Yes
Select stitch length to perform tie stitching/return
stitching.
(0.6 / 0.8)
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
22. Return Stitches (ATH)
( -, 1, 2, )
23. Tie Stitches
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
25. Preset Halt (Stitch)
( 0 ~999999 st., )
26. Preset Halt (Data)
( 0 ~99999 cm, )
27. Preset Halt (Design)
( 0 ~999 Designs, )
28. Preset Halt (Lubrication)
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
30. Language
( English, Japnese, Other, )
0.8
When the stitch counter reaches the set value, it
will make the machine stop automatically.
Code number “1D2” will be displayed at
stop of the machine.
"0" makes no stop.
(0 ~ 999999 st.)
0
-
Yes
0.8
0
0
0
0
No
Japanese
21. Select Under T. Trimming [mm]
( 0, 5, 10, 20, 30, A, )
22. Return Stitches (ATH)
( -, 1, 2, )
23. Tie Stitches
( No, Yes, )
24. Tie/Return Stitch Length [mm]
( 0.6, 0.8, )
25. Preset Halt (Stitch)
( 0 ~999999 st., )
26. Preset Halt (Data)
( 0 ~99999 cm, )
27. Preset Halt (Design)
( 0 ~999 Designs, )
28. Preset Halt (Lubrication)
( 0 ~99 * 10000 st., )
29. Preset Halt (Just before End Code)
( No, Yes, )
30. Language
( English, Japnese, Other, )
0
Numerical key
To Next Page
Loading...
