TAJIMA TEHX-C - Lubrication; Lubrication Cycle; Bobbin Changer; Sequin(R) [MM]

CHAPTER 8 PARAMETER SETTING
88
36. Lubrication
37. Lubrication Cycle
38. Bobbin Changer
39. Sequin(R) [mm]
40. Sequin(L) [mm]
Select whether automatic lubrication system is
equipped with the machine or not.
Yes Equipped
No Not equipped
(Yes/No)
No
1
0.0
Yes
200
250
No
0
No
No
No
31. F.B/F.F. Stitch Unit [st]
( 1, 3, 5, )
32. Satin Stitch (Data to add) [mm]
( -1.0 ~ 1.0, )
33. Auto Origin Return
( No, Yes, )
34. Frame Travel Speed [mm/sec]
( 100, 200, )
35. Frame Start Timing [Degree]
( 230, 240, 250, 260, )
36. Lubrication
( No, Yes, )
37. Lubrication Cycle
( 0 ~9999 * 1000 st., )
38. Bobbin Changer
( No, Yes, )
39. Sequin(R) [mm]
( No, 5, 6, 7, 8, 9, 10, )
40. Sequin(L) [mm]
( No, 5, 6, 7, 8, 9, 10, )
(GC07)
When the stitch count reaches the set value, it will
make automatic lubrication system activate.
Setting value multiplied by 1000 stitches
It is possible to make setting when “36.
Lubrication” is set to “Yes”
(0 ~ 9999 * 1000st.)
0
1
0.0
Yes
200
250
No
0
No
No
No
31. F.B/F.F. Stitch Unit [st]
( 1, 3, 5, )
32. Satin Stitch (Data to add) [mm]
( -1.0 ~ 1.0, )
33. Auto Origin Return
( No, Yes, )
34. Frame Travel Speed [mm/sec]
( 100, 200, )
35. Frame Start Timing [Degree]
( 230, 240, 250, 260, )
36. Lubrication
( No, Yes, )
37. Lubrication Cycle
( 0 ~9999 * 1000 st., )
38. Bobbin Changer
( No, Yes, )
39. Sequin(R) [mm]
( No, 5, 6, 7, 8, 9, 10, )
40. Sequin(L) [mm]
( No, 5, 6, 7, 8, 9, 10, )
Numerical key
Select whether bobbin changer is equipped with
the machine or not.
It is not displayed in TFHX-C, TFHX-2C,
and TEHX-C.
Yes Equipped
No Not equipped
No
1
0.0
Yes
200
250
No
0
No
No
No
31. F.B/F.F. Stitch Unit [st]
( 1, 3, 5, )
32. Satin Stitch (Data to add) [mm]
( -1.0 ~ 1.0, )
33. Auto Origin Return
( No, Yes, )
34. Frame Travel Speed [mm/sec]
( 100, 200, )
35. Frame Start Timing [Degree]
( 230, 240, 250, 260, )
36. Lubrication
( No, Yes, )
37. Lubrication Cycle
( 0 ~9999 * 1000 st., )
38. Bobbin Changer
( No, Yes, )
39. Sequin(R) [mm]
( No, 5, 6, 7, 8, 9, 10, )
40. Sequin(L) [mm]
( No, 5, 6, 7, 8, 9, 10, )
(Yes/No)
Select equipment/feed amount of sequin device
(R)
5 to 10 Feed amount of chip
No Not equipped
No
1
0.0
Yes
200
250
No
0
No
No
No
31. F.B/F.F. Stitch Unit [st]
( 1, 3, 5, )
32. Satin Stitch (Data to add) [mm]
( -1.0 ~ 1.0, )
33. Auto Origin Return
( No, Yes, )
34. Frame Travel Speed [mm/sec]
( 100, 200, )
35. Frame Start Timing [Degree]
( 230, 240, 250, 260, )
36. Lubrication
( No, Yes, )
37. Lubrication Cycle
( 0 ~9999 * 1000 st., )
38. Bobbin Changer
( No, Yes, )
39. Sequin(R) [mm]
( No, 5, 6, 7, 8, 9, 10, )
40. Sequin(L) [mm]
( No, 5, 6, 7, 8, 9, 10, )
(No, 5, 6, 7, 8, 9, 10)
Select equipment/feed amount of sequin device
(L)
5 to 10 Feed amount of chip
No Not equipped
1
0.0
Yes
200
250
No
0
No
No
No
31. F.B/F.F. Stitch Unit [st]
( 1, 3, 5, )
32. Satin Stitch (Data to add) [mm]
( -1.0 ~ 1.0, )
33. Auto Origin Return
( No, Yes, )
34. Frame Travel Speed [mm/sec]
( 100, 200, )
35. Frame Start Timing [Degree]
( 230, 240, 250, 260, )
36. Lubrication
( No, Yes, )
37. Lubrication Cycle
( 0 ~9999 * 1000 st., )
38. Bobbin Changer
( No, Yes, )
39. Sequin(R) [mm]
( No, 5, 6, 7, 8, 9, 10, )
40. Sequin(L) [mm]
( No, 5, 6, 7, 8, 9, 10, )
No
(No, 5, 6, 7, 8, 9, 10)