TAJIMA TEHX-C - 19. ATH

CHAPTER 8 PARAMETER SETTING
84
16. Upper T.Detection
17. Under T.Detection (Unit)
18. Under T.D. (Step Ratio) [%]
19. ATH
20. Picker Timing (Tail Length)
When the machine detects upper thread breakage
information more than the set number of times,
make the machine recognizes that it is a state of
upper thread breakage.
When the setting value becomes smaller, the
sensitivity will become higher.
"0" does not make detection.
(0, 1, 2, 3, 4)
No
No
No
600
2
4
70
Yes
30
2
11. Frame Back All Head Sew
( No, Yes, )
12. Overlap Frame Back
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
13. Halt Frame Back
( No, Yes, )
------
15. Min. Revolution [rpm]
( 250 ~ 700, )
16. Upper T.Detection
( 0, 1, 2, 3, 4, )
17. Under T.Detection (Unit)
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
19. ATH
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )
(GC02)
When information of under thread breakage is
detected the number of set times and more consec-
utively, it is regarded as a state of under thread
breakage.
When the setting value becomes smaller, the
sensitivity will become higher.
"0" does not make detection.
(0, 2, 4, 6, 8)
No
No
No
600
2
4
70
Yes
30
4
11. Frame Back All Head Sew
( No, Yes, )
12. Overlap Frame Back
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
13. Halt Frame Back
( No, Yes, )
------
15. Min. Revolution [rpm]
( 250 ~ 700, )
16. Upper T.Detection
( 0, 1, 2, 3, 4, )
17. Under T.Detection (Unit)
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
19. ATH
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )
It adjusts sensitivity of thread breakage detection.
When the setting value becomes bigger, the
sensitivity will become higher.
(40, 50, 60, 70, 80%)
No
No
No
600
2
4
70
Yes
30
70
11. Frame Back All Head Sew
( No, Yes, )
12. Overlap Frame Back
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
13. Halt Frame Back
( No, Yes, )
------
15. Min. Revolution [rpm]
( 250 ~ 700, )
16. Upper T.Detection
( 0, 1, 2, 3, 4, )
17. Under T.Detection (Unit)
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
19. ATH
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )
It makes the machine to perform automatic thread
trimming at color change, end of embroidery, etc.
Yes To perform thread trimming
No Not to perform thread trimming
(Yes/No)
No
No
No
600
2
4
70
Yes
30
Yes
11. Frame Back All Head Sew
( No, Yes, )
12. Overlap Frame Back
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
13. Halt Frame Back
( No, Yes, )
------
15. Min. Revolution [rpm]
( 250 ~ 700, )
16. Upper T.Detection
( 0, 1, 2, 3, 4, )
17. Under T.Detection (Unit)
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
19. ATH
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )
It adjusts the remaining thread length at thread
trimming.
It is possible to make setting when “19.
ATH” is set to “Yes”
340 20 60
Short Long
(340 ~ 359, 0 ~ 60 deg.)
No
No
No
600
2
4
70
Yes
30
30
11. Frame Back All Head Sew
( No, Yes, )
12. Overlap Frame Back
( No, 1, 2, 3, 4, 5, 6, 7, 8, 9, )
13. Halt Frame Back
( No, Yes, )
------
15. Min. Revolution [rpm]
( 250 ~ 700, )
16. Upper T.Detection
( 0, 1, 2, 3, 4, )
17. Under T.Detection (Unit)
( 0, 2, 4, 6, 8, )
18. Under T.D. (Step Ratio) [%]
( 40, 50, 60, 70, 80, )
19. ATH
( No, Yes, )
20. Picker Timing (Tail Length)
( 340 ~359, 0 ~ 60 deg, )