TAJIMA TEHX-C - Serial Speed [Bps]; Backlash (X Axis) [MM]; Backlash (y Axis) [MM]

CHAPTER 8 PARAMETER SETTING
90
46. Serial Speed [bps]
47. ------
48. Table Up/Down
49. Backlash (X Axis) [mm]
50. Backlash (Y Axis) [mm]
Select transfer speed of serial connector.
It is possible to make setting when “Yes” is
set to “45. Network”.
(9600, 19200, 38400)
38400
No
Step1
No
No
38400
No
0.0
0.0
41. Boring
( No, Yes, )
42. Boring Step
( Step1, Step3, )
43. Cording
( No, Yes, )
------
45. Network
( No, Yes, )
46. Serial Speed [bps]
( 9600, 19200, 38400, )
------
48. Table Up/Down
( No, Yes, )
49. Backlash (X Axis) [mm]
( -0.5 ~ 0.5, )
50. Backlash (Y Axis) [mm]
( -0.5 ~ 0.5, )
(GC07)
It is not applied.
No
Step1
No
No
38400
No
0.0
0.0
41. Boring
( No, Yes, )
42. Boring Step
( Step1, Step3, )
43. Cording
( No, Yes, )
------
45. Network
( No, Yes, )
46. Serial Speed [bps]
( 9600, 19200, 38400, )
------
48. Table Up/Down
( No, Yes, )
49. Backlash (X Axis) [mm]
( -0.5 ~ 0.5, )
50. Backlash (Y Axis) [mm]
( -0.5 ~ 0.5, )
Select whether auto sub-table lifter is equipped
with the machine or not.
Setting is applied to TEHX-C only
Yes Equipped
No Not equipped
No
No
Step1
No
No
38400
No
0.0
0.0
41. Boring
( No, Yes, )
42. Boring Step
( Step1, Step3, )
43. Cording
( No, Yes, )
------
45. Network
( No, Yes, )
46. Serial Speed [bps]
( 9600, 19200, 38400, )
------
48. Table Up/Down
( No, Yes, )
49. Backlash (X Axis) [mm]
( -0.5 ~ 0.5, )
50. Backlash (Y Axis) [mm]
( -0.5 ~ 0.5, )
(Yes/No)
It corrects mechanical error generated when
movement of the X-axis drive system reverses.
"0" does not make correction.
When correction is made, “32. Satin Stitch
(Data to add)” will become invalid.
Backlash p.99
0.0
No
Step1
No
No
38400
No
0.0
0.0
41. Boring
( No, Yes, )
42. Boring Step
( Step1, Step3, )
43. Cording
( No, Yes, )
------
45. Network
( No, Yes, )
46. Serial Speed [bps]
( 9600, 19200, 38400, )
------
48. Table Up/Down
( No, Yes, )
49. Backlash (X Axis) [mm]
( -0.5 ~ 0.5, )
50. Backlash (Y Axis) [mm]
( -0.5 ~ 0.5, )
(-0.5 ~ 0.5 mm)
It corrects mechanical error generated when
movement of the Y-axis drive system reverses.
"0" does not make correction.
When correction is made, “32. Satin Stitch
(Data to add)” will become invalid.
Backlash p.99
(-0.5 ~ 0.5 mm)
No
Step1
No
No
38400
No
0.0
0.0
41. Boring
( No, Yes, )
42. Boring Step
( Step1, Step3, )
43. Cording
( No, Yes, )
------
45. Network
( No, Yes, )
46. Serial Speed [bps]
( 9600, 19200, 38400, )
------
48. Table Up/Down
( No, Yes, )
49. Backlash (X Axis) [mm]
( -0.5 ~ 0.5, )
50. Backlash (Y Axis) [mm]
( -0.5 ~ 0.5, )
0.0