Technogym Runrace - 4. ACCESSORIES; 4.1. CONNECTING TO THE TGS; 4.2. CONNECTING TO THE PRINTER; 4.3. CONNECTING TO AN EXTERNAL DEVICE (ECG AND;OR METABOLIC MONITOR)

RUNRACE : Service & Maintenance Manual - rev. 2.0
Page ii
4.4.1. RS-232 Port..................................................................................................................................4.4
4.4.2. RS-485 Ports ................................................................................................................................4.4
5. INSTALLATION INSTRUCTIONS ....................................................................................................................5.1
5.1. SPECIFICATIONS AND REQUIREMENTS.......................................................................................................... 5.1
5.2. I
NSTALLATION............................................................................................................................................. 5.1
5.3. F
IRST POWER-ON ......................................................................................................................................... 5.2
6.
TROUBLESHOOTING.........................................................................................................................................6.1
6.1. THE DISPLAY DOES NOT ILLUMINATE........................................................................................................... 6.2
6.2. T
HE LCD SHOWS “EMERGENCY PRESSED: EXERCISE INTERRUPTED” ........................................ 6.6
6.3. T
HE INVERTER IS OFF .................................................................................................................................. 6.7
6.4. T
HE LCD SHOWS “BELT MOTOR HALTED”........................................................................................ 6.10
6.4.1.
The inverter display shows E01, E02, E03, E04 or E05 ............................................................6.12
6.4.2. The inverter display shows E6 or E7..........................................................................................6.14
6.4.3. The inverter display shows E8, E10 or E11 ...............................................................................6.15
6.4.4. The inverter display shows E09..................................................................................................6.16
6.4.5. The inverter display shows E12..................................................................................................6.18
6.4.6. The inverter display shows E14..................................................................................................6.19
6.4.7. The inverter display shows E15..................................................................................................6.20
6.4.8. The inverter display shows E21..................................................................................................6.22
6.4.9. The inverter display does not show any error ............................................................................6.23
6.5. THE BELT MOTOR IS JERKING..................................................................................................................... 6.25
6.6. T
HE BELT MOTOR STARTS WITH DELAY ..................................................................................................... 6.26
6.7. T
HE DISPLAYED SPEED IS INCORRECT........................................................................................................ 6.28
6.8. T
HE LCD SHOWS “GRADE MOVEMENT OUT OF ORDER”............................................................... 6.31
6.9. T
HE UP-DOWN MOVES IN ONLY ONE DIRECTION ........................................................................................ 6.36
6.10. T
HE DISPLAYED ELEVATION IS INCORRECT ................................................................................................ 6.39
6.11. T
HE LCD SHOWS “WARNING: CHECK BATTERY” ............................................................................ 6.41
6.12. T
HE LCD SHOWS “BELT LUBRICANT OUT: REFILL”........................................................................ 6.41
6.13. T
HE LUBRICATION CIRCUIT DOES NOT WORK............................................................................................. 6.42
6.14. T
HE MACHINE DOES NOT PRINT ................................................................................................................. 6.44
6.15. T
HERE IS NO HEART RATE SIGNAL ............................................................................................................. 6.46
6.16. T
HE HEART RATE SIGNAL IS INCORRECT .................................................................................................... 6.47
7.
DISASSEMBLY OF COMPONENTS .................................................................................................................7.1
7.1. DISASSEMBLING THE DISPLAY ..................................................................................................................... 7.1
7.2. D
ISASSEMBLING THE EPROM..................................................................................................................... 7.2
7.3. D
ISASSEMBLING THE BACKUP BATTERY ...................................................................................................... 7.3
7.4. D
ISASSEMBLING THE CPU BOARD .............................................................................................................. 7.4
7.5. D
ISASSEMBLING THE KEYBOARD................................................................................................................. 7.6
7.6. D
ISASSEMBLING THE CARDIO RECEIVER...................................................................................................... 7.8
7.7. D
ISASSEMBLING THE EMERGENCY STOP BUTTON ........................................................................................ 7.9
7.8. D
ISASSEMBLING THE MOTOR GUARD ......................................................................................................... 7.10
7.9. D
ISASSEMBLING THE SIDE GUARDS............................................................................................................ 7.11
7.10. D
ISASSEMBLING THE FRONT PLATE ........................................................................................................... 7.12
7.11. D
ISASSEMBLING SHIELD GRID FOR TREAD BELT MOTOR AND INVERTER .................................................... 7.13
7.12. D
ISASSEMBLING THE REAR ROLLER ........................................................................................................... 7.14
7.13. D
ISASSEMBLING THE MOTOR ROLLER ........................................................................................................ 7.16
7.14. D
ISASSEMBLING THE BRUSH...................................................................................................................... 7.17
7.15. D
ISASSEMBLING THE TREAD BELT AND RUNNING TRACK........................................................................... 7.18
7.16. D
ISASSEMBLING THE SHOCK ABSORBERS .................................................................................................. 7.20
7.17. D
ISASSEMBLING THE TREAD-BELT MOTOR ................................................................................................ 7.21
7.18. D
ISASSEMBLING THE MOTOR DRIVE-BELT ................................................................................................. 7.23
7.19. D
ISASSEMBLING THE ELECTRONIC CIRCUIT BOARDS.................................................................................. 7.24
7.20. D
ISASSEMBLING THE INVERTER................................................................................................................. 7.26
7.21. D
ISASSEMBLING THE UP-DOWN MOTOR BELT ............................................................................................ 7.27
7.22. D
ISASSEMBLING THE UP-DOWN MOTOR..................................................................................................... 7.28