Technogym Runrace - 7. DISASSEMBLY OF COMPONENTS; 7.1. DISASSEMBLING THE DISPLAY; 7.2. DISASSEMBLING THE EPROM; 7.3. DISASSEMBLING THE BACKUP BATTERY

RUNRACE : Service & Maintenance Manual - rev. 2.0
Page iii
7.23. DISASSEMBLING THE UP-DOWN MOTOR BRUSHES...................................................................................... 7.31
7.24. D
ISASSEMBLING THE ELEVATION BARS ..................................................................................................... 7.32
7.25. D
ISASSEMBLING THE LEAD SCREW NUTS ................................................................................................... 7.33
7.26. D
ISASSEMBLING THE MICROSWITCHES ...................................................................................................... 7.34
7.27. D
ISASSEMBLING THE PHOTOCELL.............................................................................................................. 7.35
7.28. D
ISASSEMBLING THE FANS ........................................................................................................................ 7.36
8.
ADJUSTMENTS ....................................................................................................................................................8.1
8.1. TENSIONING A NEW TREAD BELT ................................................................................................................. 8.1
8.2. T
ENSIONING A USED TREAD BELT ................................................................................................................ 8.2
8.3. C
ENTERING THE TREAD BELT ...................................................................................................................... 8.3
8.4. A
DJUSTING THE TENSION AND ALIGNMENT OF THE TREAD-BELT MOTOR BELT............................................. 8.4
8.5. T
ENSIONING THE UP-DOWN MOTOR BELT .................................................................................................... 8.6
8.6. A
LIGNING THE ELEVATION BARS ................................................................................................................. 8.7
8.7. C
ALIBRATING THE TREAD BELT SPEED......................................................................................................... 8.8
8.8. C
ENTERING THE PHOTOCELL ....................................................................................................................... 8.9
8.9. A
DJUSTING THE LCD BACKLIGHTING........................................................................................................ 8.10
8.10. A
DJUSTING THE BUZZER TONE................................................................................................................... 8.11
9.
MACHINE CONFIGURATION...........................................................................................................................9.1
9.1. HW MACHINE CONFIGURATION ................................................................................................................... 9.1
9.1.1.
Enable use of external device.......................................................................................................9.1
9.1.2. Language configuration ...............................................................................................................9.1
9.1.3. External device interface configuration.......................................................................................9.1
9.2. CONFIGURATION OF SW PARAMETERS ........................................................................................................ 9.3
9.3. P
ARTIAL DISPLAY OF WORKING PARAMETERS.............................................................................................. 9.4
9.3.1.
Machine utilization.......................................................................................................................9.4
9.3.2. Type of lubrication .......................................................................................................................9.4
9.3.3. Distance covered since the last lubrication..................................................................................9.4
9.3.4. Number of manual lubrication cycles ..........................................................................................9.5
9.3.5. Number of automatic lubrication cycles.......................................................................................9.5
9.3.6. Total lubrication time...................................................................................................................9.5
9.4. COMPLETE DISPLAY OF WORKING PARAMETERS .......................................................................................... 9.6
9.4.1.
Machine utilization.......................................................................................................................9.6
9.4.2. Lubrication interval......................................................................................................................9.6
9.4.3. Duration of automatic lubrication ...............................................................................................9.6
9.4.4. Distance covered since the last lubrication..................................................................................9.6
9.4.5. Number of manual lubrication cycles ..........................................................................................9.7
9.4.6. Number of automatic lubrication cycles.......................................................................................9.7
9.4.7. Total lubrication time...................................................................................................................9.7
9.5. MODIFYING THE WORKING PARAMETERS..................................................................................................... 9.8
9.5.1.
Total hours ...................................................................................................................................9.8
9.5.2. Distance covered..........................................................................................................................9.8
9.5.3. Lubrication interval......................................................................................................................9.8
9.5.4. Lubrication duration ....................................................................................................................9.9
9.6. PROGRAMMING THE HITACHI SJ100 INVERTER...................................................................................... 9.10
9.6.1.
Modified parameter settings.......................................................................................................9.11
9.6.2. Monitor function parameters......................................................................................................9.11
9.7. PROGRAMMING THE HITACHI J100 INVERTER ........................................................................................ 9.12
9.7.1.
Version E2..................................................................................................................................9.12
9.7.2. Versions E3, E4 and E5 .............................................................................................................9.12
9.8. PROGRAMMING THE LENZE 644 INVERTER ............................................................................................. 9.15
10.
SCHEDULED MAINTENANCE........................................................................................................................10.1
10.1. EXTERNAL CLEANING OPERATIONS ........................................................................................................... 10.1
10.1.1.
Setting up the operation .............................................................................................................10.1
10.1.2. Cleaning operations...................................................................................................................10.1
10.2. ROUTINE MAINTENANCE OPERATIONS ....................................................................................................... 10.2