Programming the Control Panel Premier 412/816/832 Installation Manual
42 INS159-13
Keypad Options 1
The operation of Keypad Options 1 is described as follows:
Partition 1 Operation
On: The selected keypad is assigned to Partition 1.
Off: The selected keypad is not assigned to Partition 1.
Partition 2 Operation
On: The selected keypad is assigned to Partition 2.
Off: The selected keypad is not assigned to Partition 2.
Partition 3 Operation (Premier 816/832 Only)
On: The selected keypad is assigned to Partition 3.
Off: The selected keypad is not assigned to Partition 3.
Partition 4 Operation (Premier 816/832 Only)
On: The selected keypad is assigned to Partition 4.
Off: The selected keypad is not assigned to Partition 4.
Permanent Keypad Status Display
On: The keypad status will be displayed permanently.
Off: Keypad status (not just zone status) will blank after the
courtesy timer has expired.
Press Any Key for Display
On: If Keypad Option 1.5 (above) is selected as disabled, the
selected keypad will re-enable the display after any key press.
Off: The selected keypad display will only re-enable after a valid
Access code has been entered.
Display Zones vs. Partitions
On: The selected keypad will use its zone lights to indicate zone
status details.
Off: The selected keypad will use its zone lights to indicate armed
status of partitions.
Wrong Code Attempts Cause Code Tamper
On: The selected keypad will lockout key presses for 5 minutes
and will generate a code tamper alarm after 3 incorrect code
attempts (12 key presses).
Off: The keypad will accept any amount of incorrect code attempt
entries.
Keypad Options 2
The operation of Keypad Options 2 is described as follows:
Code Tamper Causes a Tamper Alarm
On: If a code tamper is generated by the selected keypad, the
system will give a tamper alarm response.
Off: If a code tamper is generated by the selected keypad, the
system will lock out the keypad for 5 minutes.
Keypad Options 1.8 must also be enabled.
Keypad Activation of Fire Alarm
On: The selected keypad will generate an emergency Fire alarm if
keys and are pressed at the same time.
Off: The selected keypad will not generate an emergency Fire
alarm.
Keypad Activation of Medical Alarm
On: The selected keypad will generate an emergency Medical
alarm if keys and are pressed at the same time.
Off: The selected keypad will not generate an emergency Medical
alarm.
Keypad Activation of PA Alarm
On: The selected keypad will generate a Panic Alarm (Police) if
keys and are pressed at the same time.
Off: The selected keypad will not generate an emergency Panic
Alarm.
Keypad PA Alarm is Silent
On: The selected keypad will generate a silent Panic Alarm
(Police) if keys and are pressed at the same time.
Off: The selected keypad will generate an audible Panic Alarm
(Police) if keys and are pressed at the same time.
Keypad Options 2.4 must also be enabled.
Quick Arm with Keypad ARM Key
On: The selected keypad can be used to quick arm the system
(Access code not required).
Off: An Access code must be entered before the selected keypad
can be used to arm the system.
Quick Disarm with Keypad DISARM Key
On: The selected keypad can be used to quick disarm the system
(Access code not required).
Off: An Access code must be entered before the selected keypad
can be used to disarm the system.
Quick Bypass with Keypad BYPASS Key
On: The selected keypad can be used to quick bypass zones
(Access code not required).
Off: An Access code must be entered before the selected keypad
can be used to bypass zones.
Keypad Options 3
The operation of Keypad Options 3 is described as follows:
Fire Alarm Tones from Keypad
On: The internal sounder for the selected keypad will produce Fire
Alarm tones.
Off: Fire Alarm tones will not be produced.
Burglary Alarm Tones from Keypad
On: The internal sounder for the selected keypad will produce
Burglary Alarm tones.
Off: Burglary Alarm tones will not be produced.
Service Tones from Keypad
On: The internal sounder for the selected keypad will produce
Service tones.
Off: Service tones will not be produced.
Acceptance Tones from Keypad
On: The internal sounder for the selected keypad will produce
Acceptance tones.
Off: Acceptance tones will not be produced.
Error Tones from Keypad
On: The internal sounder for the selected keypad will produce
Error tones.
Off: Error tones will not be produced.
Chime Tones from Keypad
On: The internal sounder for the selected keypad will produce
Chime tones.
Off: Chime tones will not be produced.
Exit Tones from Keypad
On: The internal sounder for the selected keypad will produce Exit
tones.
Off: Exit tones will not be produced.
To Next Page
Loading...
