Texecom Premier 412 - Page 83

Premier 412/816/832 Installation Manual Quick Reference Guide
INS159-13 83
Menu
Function
Page
Programming System Outputs

Panel Outputs
47

Fast Format Channels
47

Expander 1 Outputs
47

Expander 2 Outputs
47

Expander 3 Outputs
47

Keypad Outputs
47
 System Output Types
00 Courtesy
01 Successful Transmission
02 Log 80% Full
03 Program Mode Selected
04 Download In Progress
05 Timed Arming Countdown
06 Zone Soak Test Active
07 Zone Soak Test Failed
08 Latched AC Fail
09 Telephone Line Fault
10 Smoke Alarm
11 Box/Auxiliary Tamper
12 Date Time Loss
13 Zone Trouble/Tamper
14 Keypad Tamper/Removed
15 Service Fault
16 Output 1 Fault
17 Output 2 Fault
 Partition Output Types
00 PA Alarm
01 Duress Alarm
02 Burglar Alarm
03 Medical Alarm
04 24Hr - Water Alarm
05 24Hr - Gas Alarm
06 24Hr - Low Temp Alarm
07 24Hr - High Temp Alarm
08 Tamper
09 Trouble
10 Fire
11 Fire Fault
12 Bell
13 Strobe
14 Entry
15 Exit
16 Armed
17 Stay Armed
18 Ready
 Zone Output Types
01 - 32 Zone Mimic 01 - 32
Output Attributes
1 Partition 1
2 Partition 2
3 Partition 3
4 Partition 4
18 Siren/Bell Fault
19 Smoke Sensor Fault
20 Auxiliary Fuse Fault
21 Latched Battery Fault
22 Service Required/Test Fail
23 Fail To Communicate
24 Control Timer 1 Active
25 Control Timer 2 Active
26 Control Timer 3 Active
27 Control Timer 4 Active
28 PC Output 1
29 PC Output 2
30 Walk Test
31 Confirmed Alarm
32 ARC 2 Active
33 Zones Locked Out
34 AC Fail
35 Battery Fault
36 Poll Timer
19 Bypass
20 Sensor Reset on Exit
21 Sensor Reset on Reset
22 Single Pulse on Arming
23 Double Pulse on Arming
24 Chime
25 Door Strike
26 Cross Zone Time Active
27 Single Pulse on Disarming
28 Reset Required
29 Acknowledgement Required
30 Confirmed Alarm
31 Alarm Abort
32 Away Armed
33 Away Armed/Exit
34 Detector Latch
35 Armed/Alarm
36 Arm Failed
37 All Armed
33 - 64 Zone Alarm 01 - 32
5 User Test
6 Inverted
7 Latching
8 Pulsed
Menu
Function
Page
Programming The Communicator

Communicator Options
52
 Enable On-Board Communicator
 Enable DTMF Dialling
 Switch to Pulse Dialling after 3
rd
Attempt
 Enable European Pulse Dialling
 Enable Auto Test Transmission
 Enable Cancel Call Waiting
 Enable Backup to Alarm Receiving Centre
 Enable Blind Dialling

ARC 1 Communicator Menu
52
 Primary and secondary telephone numbers
 Account Numbers (partitions 1-4)
 Protocol Type:
 Disabled
 Pulse Format
 Express Format
 Fast Format/Speech Module
 Contact ID
 SIA Level 2/3
 Pager
 Mobile Phone
 Dial Attempts
 Partition Options:
 Report for Partition 1
 Report for Partition 2
 Report for Partition 3
 Report for Partition 4
 Reporting Options:
 Priority Alarm and Cancel Events
 Alarm and Cancel Events
 Open and Close Events
 Bypass and Unbypass Events
 Maintenance Alarm Events
 Tamper Alarm Events
 Test Transmission Events
 Restore Events
 Pulse Format Options:
 Use 1900Hz Carrier
 Use 40 PPS Baud Rate
 Enable Parity
 Use 2 Digit Events
 Use 2300Hz Handshake
 Use 2300Hz Kiss-Off
 Use Fast/Slow Format
 Fast Format/Speech Reporting Channels
 Report Channel 1
 Report Channel 2
 Report Channel 3
 Report Channel 4
 Report Channel 5
 Report Channel 6
 Report Channel 7
 Report Channel 8
 Protocol Options:
 Disable SIA Modifier Blocks/Enable Speech Module
 Disable Events for Each Partition
 Pager Terminator = * (Star)
 Send Pager Terminator Twice/Send SIA Text
 Pager DTMF Tones = 500mS
 Disable Zone Restorals
  Communication Acknowledgement Tone
  Connect via IP