Toro ProCore 648s - Aerator Maintenance; Checking the Fastener Torque; Adjusting the Side Shields

To Next Page

To Previous Page

g010064

Figure182

1.Sideshield

3.Adjusttheshieldupordownuntilyoumeasure

a25to38mm(1to1.5inches)betweenthe

shieldandtheground.

4.Tightenthecapscrewsandangelocknuts.

5.Repeatsteps2through4attheothersideof

themachine.

ReplacingtheTurfGuards

Replaceturfguardsiftheyarebroken,orworntoless

than6mm(1/4inch)thickness.Brokenturfguards

cancatchandteartheturf,damagingit.

g010068

Figure183

1.Turfguard

CoringHeadTiming

Thecoringheadtimingmarksareeasilyidentiedby

thecast-inmarksonthe3bearinghousings.

g341348

Figure184

1.Timingmarks

Main Page

Table of Contents3
Safety4
General Safety4
Safety and Instructional Decals5
Setup11
Installing the Rear Wheels12
Installing the Handle12
Charging and Connecting the Battery15
Installing the Rear Hood Latch Lock16
Installing the Belt-Cover Latch Lanyard17
Applying the CE Decal and the Production Year Decal18
Installing the Tine Holders, Turf Guards, and Tines18
Product Overview19
Controls19
Handlebar Controls19
Traction Controls20
Coring Head Controls20
Engine Controls21
Specifications25
Attachments/Accessories25
Before Operation26
Before Operation Safety26
Adding Fuel26
Performing Daily Maintenance27
Testing the Safety Interlock System27
Installing Turf Guards, Tine Holders, and Tines29
Hole Depth, Hole Spacing, and Tine Settings31
Setting the Hole Depth33
Setting the Hole Spacing33
Setting Tine Diameter34
Setting the Tines Quantity35
Calibrating the Tine Ground Height36
During Operation38
During Operation Safety38
Slope Safety38
Engaging Parking Brake39
Releasing the Parking Brake39
Starting the Engine40
Shutting off the Engine40
Using the Machine41
Using the Line Marker47
Using Aerator Statistics for Estimating Topdressing47
Supporting the Coring Head with the Service Latch50
Stowing the Service Latch50
Replacing a Damaged Tine51
Checking the Tine Ground-Height Calibration51
Adjusting the Weight Transfer52
Using Manual Ground Following53
Stowing the Depth-Stop Spacers for Automatic Ground Following55
Adding Additional Weight56
Moving the Machine by Hand56
Moving the Machine When the Coring Head Is Lowered57
Operating Tips58
After Operation61
After Operation Safety61
Cleaning the Machine61
Tie-Down Points61
Hauling the Machine62
Maintenance63
Maintenance Safety63
Recommended Maintenance Schedule(S)63
Daily Maintenance Checklist64
Pre-Maintenance Procedures65
Preparing the Machine for Maintenance65
Lifting the Machine65
Removing the Belt Cover66
Installing the Belt Cover67
Removing the Coring-Head Cover68
Installing the Coring-Head Cover69
Lubrication70
Checking the Coring Head Bearings70
Engine Maintenance71
Engine Safety71
Servicing the Air Cleaner71
Engine Oil Specification72
Checking the Engine-Oil Level72
Changing the Engine Oil and Filter73
Servicing the Spark Plugs74
Cleaning the Engine Screen75
Fuel System Maintenance75
Replacing the Fuel Filter75
Draining the Fuel Tank76
Electrical System Maintenance77
Electrical System Safety77
Servicing the Battery77
Replacing the Fuses78
Drive System Maintenance79
Checking the Tire Pressure79
Belt Maintenance79
Inspecting the Belts79
Adjusting the Pump Belt79
Hydraulic System Maintenance80
Hydraulic System Safety80
Relieving Hydraulic Pressure80
Checking the Hydraulic Lines81
Hydraulic Fluid Specifications81
Checking the Hydraulic-Fluid Level82
Changing the Hydraulic Fluid and Filters82
Aerator Maintenance83
Checking the Fastener Torque83
Adjusting the Side Shields83
Replacing the Turf Guards84
Coring Head Timing84

Toro ProCore 648s - Aerator Maintenance; Checking the Fastener Torque; Adjusting the Side Shields

Table of Contents

Other manuals for Toro ProCore 648s

Related product manuals