16502 PIREG-C2 Gerätebeschreibung mit EtherNet_IP Bussystem191017 - EN.docx/ Page 1 of 66
PIREG-C2 Device Description:
Resistance temperature controller
with EtherNet/IP interface
Applications:
Packaging machines for
sealing plastic foils
PIREG-C2 controller with EtherNet/IP
PIREG-CT-50 current transformer
Contents:
1. General, safety and warning instructions 2
1.1. Note on the device description 2
1.2. Icons and symbols 3
1.3. General safety instructions 3
1.4. Application 3
1.5. Note on the heating conductor 3
1.6. Note on the sealing transformer 4
1.7. Note on the current transformer 4
1.8. General assembly instructions 4
1.9. Maintenance 4
1.10. Validity 4
2. Short description 5
3. Operating states 5
3.1. Calibration 5
3.1.1. Initialisation 6
3.1.2. Calibrating the input amplifier 6
3.1.3. Determining the phase shift 6
3.1.4. Determining the reference resistance 6
3.1.5. Temperature comparison time 6
3.1.6. Checking the reference resistance 6
3.1.7. Determining the P-factor 6
3.1.8. 8-point Tc correction 6
3.1.9. Single-point Tc correction 8
3.1.10. P-factor correction 9
3.2. OFF state 9
3.2.1. Measurement pulse-pause 9
3.2.2. Calibration switching 9
3.3. ON state 9
3.4. Error state 9
3.4.1. Temperature monitoring 9
3.4.2. Heating monitoring 10
3.4.3. Communication monitoring 10
3.4.4. P-factor monitoring 10
3.4.5. Heating time limit 10
3.4.6. Error causes 10
3.4.7. Error memory 11
4. Operation 11
4.1. LEDs 11
4.1.1. Power 11
4.1.2. Heat 11
4.1.3. Calibration 11
4.1.4. Alarm 11
4.1.5. Bus system: 11
4.1.6. Network: 11
4.2. Inputs 11
4.2.1. Start input 11
4.2.2. Calibration start input 11
4.2.3. Reset input 12
4.2.4. Target value input 12
4.3. Outputs 12
4.3.1. Vref output 12
4.3.2. Actual value output 12
4.3.3. Alarm output 12
4.3.4. OK output 12
4.3.5. ELR output 12
4.4. Interfaces 13
4.4.1. RS232 and USB communication 13
4.4.2. Addressed RS232 communication 13
4.4.3. RS485 communication 13
4.4.4. RS232 com. with the TM6 thermom. 14
4.5. RS232 a. USB interface acknowledg. 15
4.5.1. OK acknowledgement 15
4.5.2. Error 1 acknowledgement 15
4.5.3. Error 2 acknowledgement 15
4.5.4. Error 3 acknowledgement 15
4.5.5. Error 4 acknowledgement 15
4.6. RS485 interface acknowledgements 16
4.6.1. OK acknowledgement 16
4.6.2. Command lock 16
4.6.3. Command error 16
4.6.4. Transfer error 16
4.6.5. Syntax or parameter error 16
4.7. Interface commands 17
4.7.1. AHUE command 17
4.7.2. BRAT command 18
4.7.3. BSTZ command 18
4.7.4. EINS command 18
4.7.5. EIPA command 19
4.7.6. FEKO command 21
4.7.7. FESL command 21
To Next Page
Need help?
General